TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 12,573 results View by: Thread Post Sort by
    Answered
  • RE: LAUNCHXL-CC26X2R1: How to inteprete the angle from AoA ant/ RTLS toolbox and How to config RTLS node?

    Clément
    Clément
    Resolved
    Hi, It looks like your project is moving forward, I am glad to see this. 1 & 2- I do not have much comments about your tests results. The only point I would like to stretch is the importance of the post-processing algorithms. These algorithms - also…
    • over 5 years ago
    • Bluetooth®︎
    • Bluetooth forum
  • Answered
  • RE: TIDC-CC2650-CC2592-EMK: Orderable for this TIDC

    Fredrik K
    Fredrik K
    Resolved
    Hi Alberto, The TIDC-CC2650-CC2592-EMK is a reference design only, not a kit. It is not possible to order this board. For a comparison of range performance with and without the CC2592 I recommend looking at the range calculator: www.ti.com/.../RF…
    • over 8 years ago
    • Bluetooth®︎
    • Bluetooth forum
  • RE: CC2650: Module designed based on the CC2650, the communication distance is too short.

    PM
    PM
    Hi, I observed some differences from your Schematic to our Ref Design. C15, C20 & C17 - Change it to 1pF (May not be that critical but better to check) R24 & R25 - Change it to 12pF ( DC Block is required). Did you check the Tx power and Rx…
    • over 7 years ago
    • Bluetooth®︎
    • Bluetooth forum
  • Answered
  • RE: CC1310: CC1310

    TER
    TER
    Resolved
    1) As said you can use the existing reference design. To find a BOM require a lot of testing and measurements. Unfortunately it doesn't exist any equation that could be used for easily recalculation of the values. 2) You can use www.ti.com/.../rf-range…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • CC1352P: cc1352p

    Ramin Rahamim
    Ramin Rahamim
    TI Thinks Resolved
    Part Number: CC1352P Hello, I use the TI RF Range Estimator excel file. In our system, our receiver has antenna diversity but the transmitter does not have. Should we use the estimator with diversity or without? The diversity in the excel file,…
    • over 6 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • Answered
  • RE: CC1310: PCB antenna and external antenna

    TER
    TER
    Resolved
    1) You can estimate the range with: www.ti.com/.../rf-range-estimator . The antenna on the LP is included in the excel sheet. 2) Yes. If not you get wrong impedance/ the energy goes both to the internal and external antenna at the same time 3) You can…
    • over 8 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: LAUNCHXL-CC1310: capabilities of TI15.4 stack and contiki 15.4

    PM
    PM
    Hi, Please refer to the following documents. - Integrating the 6LoWPAN Mesh Designs into a New TI-15.4 Stack Example (This explains how customers can port to a newer version of SDK) - How to Configure Different Frequency Bands…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: LAUNCHXL-CC1352P: Which wireless system is for me ?

    TER
    TER
    If your main target is range, take a look at www.ti.com/.../rf-range-estimator and find the parameters required to achieve the range you are looking for. As you will see from the spreadsheet range is dependent on a lot of factors and a fair number of…
    • over 8 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • Answered
  • RE: CC1310: CC1310: EasyLink at 200kbps or higher?

    TER
    TER
    Resolved
    EasyLink has changed slightly over time and hence the documentation could seem misleading if you find documentation that is referring to a different version than you are using. I see that you are pointing to a very old SDK version. If you are able to…
    • over 7 years ago
    • Sub-1 GHz
    • Sub-1 GHz forum
  • RE: CC1352R: Generic: usage of Zigbee for industrial applications?

    Ryan Brown1
    Ryan Brown1
    Hello GGA, e2e.ti.com/.../761393 Zigbee is commonly used in factory and building automation for industrial applications, not just home automation. Range depends on the TX power settings and environment interference but you can use the RF-RANGE…
    • over 7 years ago
    • Zigbee & Thread
    • Zigbee & Thread forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question