TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 48 results View by: Thread Post Sort by
    Answered
  • RE: TUSB501: TUSB501TDRFRQ1

    Vishesh Pithadiya
    Vishesh Pithadiya
    Resolved
    Hi, Apologies for being unclear. The original simulation was done with the SN65LVPE502a. This part has very similar performance to TUSB501. but it has two channels. The s16 file can be used as a reference. If you use data from just CH1 or CH2…
    • 5 months ago
    • Interface
    • Interface forum
  • TUSB522P: Swap SS Differential Pairs

    Mitchell
    Mitchell
    TI Thinks Resolved
    Part Number: TUSB522P Other Parts Discussed in Thread: SN65LVPE502A Hi Team, On the TUSB522P, is it acceptable to swap the SS differential pairs for ease of routing (i.e. TXP can be routed to TXN and RXN can be routed to RXP)? I see mention of this…
    • over 7 years ago
    • Interface
    • Interface forum
  • SN65LVPE502ARGER for LFPS

    kerr chang
    kerr chang
    TI Thinks Resolved
    Other Parts Discussed in Thread: SN65LVPE502A , TUSB522P , SN65LVPE512 Hi Team We test TI SN65LVPE502A usb redriver. We setting DE to Low ( -6db ) , The 5G LFPS peak - peak differential output voltage is 734mV. The Pass spec is 800mV to 1.2V. …
    • over 9 years ago
    • Interface
    • Interface forum
  • RE: SN65LVPE502: spec check

    Malik Barton57
    Malik Barton57
    Hi, SN65LVPE502A does not use pin 14 for compliance testing and should be left not connected.
    • over 4 years ago
    • Interface
    • Interface forum
  • TUSB522P: TUSB522P: pullup resistor on EN_RXD

    Luca Rigazio
    Luca Rigazio
    TI Thinks Resolved
    Part Number: TUSB522P Other Parts Discussed in Thread: SN65LVPE502A , Hello, I need to replace a SN65LVPE502A with a TUSB522P on a board already in production. On that board, pin 5 (EN_RXD) is tied to 3.3V. TUSB522P datasheet suggest a 4.7 kOhm pullup…
    • over 8 years ago
    • Interface
    • Interface forum
  • Answered
  • RE: SN65LVPE512: A reason of NRND

    Diego Cortes
    Diego Cortes
    Resolved
    Hello Shinichi, The SN65LVPE512 has connection issues with few devices, this happens wen the Host disables its SS terminations but the device doesn't (or the device has a delay).The SN65LVPE502A gives priority to the device detection; therefore it will…
    • over 8 years ago
    • Interface
    • Interface forum
  • Answered
  • TUSB501 / typical eye diagram and performance curves

    K.Yaita
    K.Yaita
    Resolved
    Other Parts Discussed in Thread: SN65LVPE502A , TUSB501 Hi Team, The datasheet of SN65LVPE502A shows "TYPICAL EYE DIAGRAM AND PERFORMANCE CURVES" at page.12-22. http://www.tij.co.jp/jp/lit/ds/symlink/sn65lvpe502a.pdf Is there the same data for TUSB501…
    • Resolved
    • over 10 years ago
    • Interface
    • Interface forum
  • withSN65LVPE502B, it can't be identified USB2.0

    Shinichi Inoue
    Shinichi Inoue
    TI Thinks Resolved
    Other Parts Discussed in Thread: SN65LVPE502A , SN65LVPE512 Dear Specialists, MY customer is evaluating with SN65LVPE502B, EZ-USB FX3(cypress) and PC. Depend on the connect sequence of 3 devices, USB2.0 connection is not recognized. The phenomenon…
    • over 10 years ago
    • Interface
    • Interface forum
  • Answered
  • RE: SN65LVPE512: SN65LVPE512 problem

    Khoa Duy Tran
    Khoa Duy Tran
    Resolved
    5811.Two USB3 repeaters in Series.pptx Michael and Undrea, Thank you for the prompt reply and the detailed explanation. That is a good news for using more than one TUSB522P added in a cascade topology. Do you expect any other signal quality and timing…
    • over 7 years ago
    • Interface
    • Interface forum
  • Answered
  • RE: TUSB551 and TUSB501/ VCM-RX

    K.Yaita
    K.Yaita
    Resolved
    Hi Diego-san, Thank you for your comment. Is there 2ch(1 lane) USB3.0 redriver that has no bias at receiver side as TUSB551? I confirmed the following devices have bias at receiver side. - SN65LVPE512 - SN65LVPE502A Best Regards, Yaita
    • over 9 years ago
    • Interface
    • Interface forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question