• SN74AHCT08: Spec of SN74AHCT08

  

  ?? ??

  Answer Suggested

  Part Number: SN74AHCT08 Tool/software: Regarding one time maximum current(AC), is it OK to refer Continuous output current(±25mA) ? Regards, Kohei Nagaoka

  • 3 months ago
  • Logic
  • Logic forum

• SN74AHCT08: SN74AHCT08

  

  Shweta chendake

  TI Thinks Resolved

  Part Number: SN74AHCT08 Tool/software: Hello team, i am using an IBIS model of SN74AHCT08PW in which ground clamp test is failed, according to IBIS quality specification The voltage column in the [GND Clamp] should extend at least from -Vcc to +Vcc…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74AHCT08: SN74AHCT08

  

  Paul Chan

  Resolved

  Part Number: SN74AHCT08 Other Parts Discussed in Thread: SN74HCS08 Tool/software: Hi, I am using this quad AND gate as shown below. In the application, the VCC pin is tied to ground and the GND pin is tied to -3.45V as I'm using negative logic. My question…

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AHCT08: Higher Output Current

  

  Brian Wang0928

  TI Thinks Resolved

  Part Number: SN74AHCT08 Other Parts Discussed in Thread: SN74LVC1G08 , ISOM8110 Tool/software: Team, Does TI have other AND gate IC that is pin-to-pin compatible with the “SN74AHCT1G08DBVR” and with a higher output current, increasing from 8 mA to…

  • 1 month ago
  • Logic
  • Logic forum
Answered

• SN74AHCT08: Expose pad connection

  

  franziskus

  Resolved

  Part Number: SN74AHCT08 Tool/software: Team, my customer uses SN74AHCT08RGYR. How do they need to connect the expose pad? The datasheet just shows vias, but not how the expose pad needs to be connected. Thanks!

  • Resolved

  • 2 months ago
  • Logic
  • Logic forum

• SN74AHCT08: SN74AHCT08PW

  

  Shweta chendake

  Part Number: SN74AHCT08 Tool/software: Hello team, i am using IBIS model of SN74AHCT08PW as this part is TTL compatible the IBIS quality specification states that the for TTL devices Temp(minimum) less than Temp(Maximum) but for given part in IBIS…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AHCT08: Thermal information for SN74AHCT08PWR

  

  ttd

  TI Thinks Resolved

  Part Number: SN74AHCT08 Dear Technical Support Team, Could you inform me of following thermal information for SN74AHCT08PWR. Datasheet seems not to have it for TSSOP(PWR) . Ｒθ jc （　　　℃ /W ） Ｒθ ja （　　　℃ /W ） Best Regards, ttd

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AHCT08: p2p device but have a higher Input transition rise or fall rate

  

  Brian Li

  Answer Suggested

  Part Number: SN74AHCT08 Other Parts Discussed in Thread: SN74HCS08 Hi team, My customer is using our SN74AHCT08. And now they have a new project which have a higher speed requirement. Could you please help check if we have a p2p device but have…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74AHCT08: About delay

  

  Liu Yang

  Resolved

  Part Number: SN74AHCT08 Hi Team, If I use SN74AHCT08PWR as a buffer for high speed serial signals of 50 MHz (about 27 ns per bit), is there any problem? If the high speed signal is inputted to the SN74AHCT08PWR, does the signal fail by the delay?…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74AHCT08: Can this device be used as a buffer from TTL(5V) to CMOS(5V)?

  

  Noriyuki Takahashi

  TI Thinks Resolved

  Part Number: SN74AHCT08 Other Parts Discussed in Thread: SN74AHCT1G08 , SN74AHCT125 , SN74AHCT1G125 , SN74LV125AT Hi team, Customer is trying to use SN74AHCT08 as a buffer from TTL(5V) to CMOS(5V). The speed is 50Mbps. Do you think whether SN74AHCT08…

  • over 2 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.