Answered

• RE: SN74AUP1G74: USING POWER-ON AS TACT SWITCH

  

  WOOYONG SUNG

  Resolved

  Thank you, sir is [Fig.2] second option right like this ? [on the first button press, Q of SN74AUP1G74 is HIGH(remain High) and then the second button press, Q of SN74AUP1G74 is LOW(remain Low) and then every button press after that will toggle…

  • over 8 years ago
  • Logic
  • Logic forum

• SN74AUP1G74: D-FF Does not respond to changes in D-Pin

  

  Eli az

  Part Number: SN74AUP1G74 Hello, I am using the D-FF with the specified part number in my application. In order to check if the device is working properly (With lack of EVB) I soldered the device on a PCB I designed and started testing it with an advantest…

  • over 8 years ago
  • Logic
  • Logic forum

• RE: SN74AUP1G74: Hello, I want to use Power-on-switch as Tact SW (Low power module) as below

  

  Emrys Maier

  Hello, I'm afraid your image did not make it through. To attach an image, start by selecting at the bottom right of the reply box. Next use the 'Insert/Edit Media' button to attach your image. This requires that the image is stored as a file somewhere…

  • over 8 years ago
  • Logic
  • Logic forum

• [SN74AUP1G74] Latch Up Precautions

  

  Benjamin Mak

  Other Parts Discussed in Thread: SN74AUP1G74 Hi Team! I am planning to use 2 SN74AUP1G74 for a clock divider. Initially, I was planning to connect the FF to the 3.3V power supply directly. However, are there any precautions that need to be taken to…

  • over 12 years ago
  • Logic
  • Logic forum

• SN74AUP1G74 datasheet confusion

  

  Michael Woi

  Other Parts Discussed in Thread: SN74AUP1G74 Hi all, I was looking over the SN74AUP1G74 datasheet and noticed that fclock at 3.3V is listed as 90MHz MAX under Timing Requirements whereas fmax at 3.3V is listed as 180MHz under Switching Characteristics…

  • over 13 years ago
  • Logic
  • Logic forum

• SN74AUC1G74: Application question

  

  Oliver Lin

  TI Thinks Resolved

  Part Number: SN74AUC1G74 Other Parts Discussed in Thread: SN74AUP1G74 Tool/software: Hi team, Could you please share some comment on below items? 1. If Vcc is 1.8V, is that ok to have 3.3V input signal? 2. Is that ok to replce SN74AUP1G74 with SN74AUC1G74…

  • 7 months ago
  • Logic
  • Logic forum
Answered

• SN74LVC1G74: Current consumption

  

  Alex M

  Resolved

  Part Number: SN74LVC1G74 Other Parts Discussed in Thread: SN74AUP1G74 Tool/software: Hi, I would like to know the current consumption of the SN74LVC1G74 flip-flop. On the datasheet, it says 10µA maximum but no typical current consumption. We want to use…

  • Resolved

  • 10 months ago
  • Logic
  • Logic forum

• SN74AUP1G17: Dynamic power

  

  Oba

  TI Thinks Resolved

  Part Number: SN74AUP1G17 Other Parts Discussed in Thread: SN74AUP2G79 , SN74AUP1G04 , SN74AUP1G74 , SN74AUP1G58 Hello My customer would like to know dynamic-power data of the below part numbers (ideally 3V VCC and about 2KHz signal). SN74AUP1G17…

  • over 3 years ago
  • Logic
  • Logic forum

• Frequency divider

  

  James Zhan

  TI Thinks Resolved

  Other Parts Discussed in Thread: SN74AUP1G17 , SN74AUP1G74 Hi team, Do we have frequency divider 30Hz input, and 15Hz output with 1.8V? Thanks.

  • over 4 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• SN74LVC1G373: What is high-impedance state for?

  

  Alex Beloff

  Resolved

  Part Number: SN74LVC1G373 Other Parts Discussed in Thread: SN74AUP1G74 , SN74AUP1G79 , SN74AUP1G17 , CSD17484F4 , SN74HCS74 , MSP430FR2000 I need to retain a HIGH/LOW state set by MCU (basically, a "bit") while the MCU is in low power (basically off)…

  • Resolved

  • over 5 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.