• SN74CB3T1G125: Need PSPICE simulation model

  

  Vidhya J

  TI Thinks Resolved

  Part Number: SN74CB3T1G125 Tool/software: Hi Team, I need PSPICE model for SN74CB3T1G125. I see only IBIS model in TI website. Thanks and Regards, Vidhya

  • 7 months ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• SN74CB3T1G125-Q1: Recommendation for RGMII 125MHz signal data SW between controller and GbE PHY

  

  Lenny Lee

  TI Thinks Resolved

  Part Number: SN74CB3T1G125-Q1 Other Parts Discussed in Thread: TS5A3166-Q1 , SN3257-Q1 Tool/software: Hi Team, Customer is looking for a Analog SW solution for 1ch RGMII signal SW between controller and GbE PHY. Control SW on/off by GPIO 1.8V…

  • 8 months ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• SN74CB3T1G125:pull-up resistor

  

  ssatake

  Resolved

  Part Number: SN74CB3T1G125 Other Parts Discussed in Thread: LSF0101 SDI-12(5Vシステム)通信を3.3Vシステムにレベルシフトしたい.SN74CB3T1G125の使用を検討しています。プルアップ抵抗なしで使用できますか?

  • Resolved

  • over 1 year ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• SN74CB3T1G125: Issue when driving A side high while B side has a 10K pull down.

  

  Magid Fazel

  Resolved

  Part Number: SN74CB3T1G125 Other Parts Discussed in Thread: SN74CBTLV1G125 Hi, We use CB3T1G125 throughout our design as a leakage prevention device instead of level shifting. Basically, we expect this part to be closed when there is power (3.3V) and…

  • Resolved

  • over 1 year ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• SN74CB3T1G125-Q1: single bit switch SC-70-5 SMD 3.3V

  

  GARETH OU

  Part Number: SN74CB3T1G125-Q1 Other Parts Discussed in Thread: SN74LVC1G07 , SN74CBTLV1G125 Hi It is recommended that the following output is open drain IC SC70-5 SMD 3.3V Or a single bit switch with OE# pin SC70-5 IC?

  • over 2 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• SN74CB3T1G125: thermal spec missing

  

  [FAE] Andrew Wang

  TI Thinks Resolved

  Part Number: SN74CB3T1G125 Hi Team, Customer is asking for Component junction temperature spec. Tjmax( ℃ )? Junction to Case Thermal Resistance θJC (℃/W) ? Please kindly support on this, thanks! Andrew

  • over 4 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• SN74CB3T1G125-Q1: Errata Sheet

  

  Danilo A.

  Resolved

  Part Number: SN74CB3T1G125-Q1 Hi Team, May I ask if we have an Errata sheet for SN74CB3T1G125-Q1? Regards, Danilo

  • Resolved

  • over 5 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• SN74CB3T1G125: IBIS model output configuration

  

  Lok Wei Hern

  TI Thinks Resolved

  Part Number: SN74CB3T1G125 Other Parts Discussed in Thread: LSF0101 The model provided does not have the capability to set for output. It can be only set for input.

  • over 5 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum

• RE: SN74CB3T1G125-Q1: Maximum Bandwidth Specification

  

  Adam Torma

  Lok, You can see in this application not that a 200MHz signal is supported by the SN74CB3T1G125 family. Thank you, Adam

  • over 6 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• SN74CB3T1G125-Q1: AEC Q100 Version to Replace SKY13370-374LF

  

  Fery Feng

  Resolved

  Part Number: SN74CB3T1G125-Q1 Other Parts Discussed in Thread: TMUX136 Hi team, Could you please help to check if we have automotive qualified SPDT switch that could replace SKY13370-374LF? Thanks

  • Resolved

  • over 6 years ago
  • Switches & multiplexers
  • Switches & multiplexers forum

Didn't find what you are looking for? Post a new question.