Search tips
Showing 47 results View by: Thread Post Sort by
    Answered

  • RE: SN74CB3T3245: About DGV (20) footprint

    Resolved
    Hi Kameron Hill, Thank you for your reply and sorry for the late reply. I followed the steps you sent me, but it didn't work. However I found an application note on DGV (20). Thin Very Small-Outline Package (SCBA009E) I hope it will be reflected in…

  • SN74CB3T3245: SN74CB3T3245 vs SN74CB3Q3345 vs SN74CBTLV3245A

    TI Thinks Resolved
    Part Number: SN74CB3T3245 Hi My customer wishes to know the key differentiation on abovementioned devices. I checked through ti.com device comparison tool, it shows the BW is different but i couldn't see those parameter recorded the datasheet, Could…

  • SN74CB3T3245: Design support

    TI Thinks Resolved
    Part Number: SN74CB3T3245 Other Parts Discussed in Thread: SN74CBTD3861 Hi, Part Number : SN74CB3T3245; which has absolute maximum rating for Vcc = 7V. But the recommended rating and waveform given for 2.3V(min) to 3.6V(max). We have planned to supply…
    • Answered

  • SN74CB3T3245: Unused pin / Control Input

    Resolved
    Part Number: SN74CB3T3245 Hi team, On the datasheet of SN74CB3T3245, it is mentioned that “All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.”. Which pins are the control inputs? At first…
    • Resolved
    • Answered

  • SN74CB3T3245: Package Question

    Resolved
    Part Number: SN74CB3T3245 The SN74CB3T3245 seems to have a DW package. The Package Drawing is listed as "DW0020A". But I have a customer asking if this package is the same as " DW (R-PDSO-G20)"? (They are going through and organizing…
    • Resolved
    • Answered

  • SN74CB3T3245: I2C interface with SN74CB3T3245 bus switch

    Resolved
    Part Number: SN74CB3T3245 Other Parts Discussed in Thread: SN74LVC2G66 I have a question about using SN74CB3T3245 as a bus switch for I2C interface. No voltage translation needed, 3.3V levels at both sides of the switch. SDA is bidirectional, SCL is unidirectional…
    • Resolved

  • SN74CB3T3245: Bus switch can be used between S6E2C series controller and MR2A16AVYS35

    TI Thinks Resolved
    Part Number: SN74CB3T3245 We are planning to interface MRAM MR2A16AVYS35 with external bus interface of S6E2C series controller. Supply voltage of MRAM is 3.3V and S6E2C controller is 5V. The communication will be bidirectional. For the above interface…
    • Answered

  • SN74CB3T3245: PCI pull up resistors

    Resolved
    Part Number: SN74CB3T3245 Hello, I intend to use SN74cb3t3245 as buffer for a PC104-P board design (PCI bus) . The SN74cb3t3245 is used to translate from a 3.3V/5V PCI bus to a 3.3V FPGA IOs. The FPGA IOs are pulled up internally. What will be the best…
    • Resolved

  • SN74CB3T3245: Judgment of reliability when voltage exceeding Vi/o is applied

    TI Thinks Resolved
    Part Number: SN74CB3T3245 【Question】SN74CB3T3245 Reliability Determination.xlsx
    • Answered

  • SN74CB3T3245: SN74CB3T3245：The output level is higher than the supply voltage

    Resolved
    Part Number: SN74CB3T3245 hi All SN74CB3T3245：The output level is higher than the supply voltage We are replacing PI3C3245 with SN74CB3T3245. In the case of VCC 2.5V power supply, the signal level on the A side is 3.3V, and the signal level on the B side…
    • Resolved

Didn't find what you are looking for? Post a new question.