Search tips
Showing 20 results View by: Thread Post Sort by
    Answered

  • TS5A21366 and SN74CB3T3306 - the ‎resistance value in case of switch OFF

    Resolved
    Other Parts Discussed in Thread: TS5A21366 , SN74CB3T3306 Hi all Would you mind if we ask TS5A21366 and SN74CB3T3306? In case of switch OFF, is it possible to regard the value as Hi-z(∞)? Kind regards, Hirotaka Matsumoto
    • Resolved
    • Answered

  • Question about SN74CB3T3306

    Resolved
    Other Parts Discussed in Thread: SN74CB3T3306 , TCA9517A Hi, I have some questions about SN74CB3T3306. I have a plan to use this device on using different power (using system A and B). The power-up sequence is difference between system A and B. 1) Can…
    • Resolved

  • SN74CB3T3306 for 148MHz Clock

    Other Parts Discussed in Thread: SN74CB3T3306 , DS90LV001 , TS5A3157 Hi, Our cutomer is considering to use SN74CB3T3306 for 148.5MHz clock. Can you use SN74CB3T3306 for 148.5MHz clock switch / level shifter ? I couldn't find the operating frequency range…

  • SN74CB3T3306

    Other Parts Discussed in Thread: SN74CB3T3306 as for SN74CB3T3306, the datasheet shows that: Absolute Maximum Ratings: VCC Supply voltage range(2) –0.5~ 7 V Recommended Operating Conditions: VCC Supply voltage 2.3 ~3.6 V Why do the two reatings have…
    • Answered

  • RE: SN74CB3Q3306A: Cross comparison against pi3vt3306uex

    Resolved
    Hi, Arthur, The SN74CB3T3306 is gonna be the closest equivalent, which offers the same translating capability as the PI3VT3306 and offered in the similar SSOP package. Thanks, David

  • RE: Using SN74CBTD3306 signals pass through despite output disabled

    Ahmad , sn74CB3T3306 works at 3.3Vcc ,however CBTD needs 5V to operate . The CBTD has an internal diode which drops down the Vcc voltage at the gate of the transistors . you can also read the blog about the different CBT switches available .
    • Answered

  • RE: SN74CBTD1G384/5 – About Tolerant I/O function

    Resolved
    The CBTD devices are 5V to 3.3V translators. The Vcc should be 5V so when Vcc is 5V they are 5V tolerant on the inputs and the output will be 3.3V. Sinc they are simple Nchannel FET's they willl be off when Vcc = 0V and there will be no leakage so even…

  • Re: logic level shifter

    Hi Todd I am not sure what you are requesting. Do you want a 4 bit translator that can translate bothe directions? If so Here are some options 1 x SN74AVC4T245 dual vcc voltage translator. 2 x SN74CB3T3306 or 1 x SN74CB3T3245 both of these require…
    • Answered

  • Re: OMAP-L138 I2C - spike on SCL

    Resolved
    Hi Abhijit, The spike occures at every 0 to 1 transition at I2C bus frequencies 400kHz and 100kHz. The oscillogram above was captured in the following board configuration (a part of multiboard device): Two TLV320AIC34 codecs are disconnected by…

  • Re: Interfacing 5V level Uart Peripherie with CC2530 Uart (3V)

    Thank you for response, in my case it is not a RS232 communication it is only a communication with device (As sensor) using UART (Tx and Rx) communication. After a long time research I fanid this level converter SN74CB3T3306.

Didn't find what you are looking for? Post a new question.