• SN74LVTH16245A: The difference between SN74LVTH16425 and SN74LVTH125

  

  R.Fukunaga

  Part Number: SN74LVTH16245A Other Parts Discussed in Thread: SN74LVTH125 Hi all, I would like to know the difference between SN74LVTH16425 and SN74LVTH125. This is the waveform during short-circuit test for each device. Ch1:output voltage Ch4:output c…

  • 3 months ago
  • Logic
  • Logic forum
Answered

• SN74LVTH125: Source current damage threshold on short to gnd fault.

  

  Anton Grounds

  Resolved

  Part Number: SN74LVTH125 Hi, Under the specification document, I do not see a value given for the damaged current if the output drive is high and the output is shorted to ground or connected to a low-impedance sink. Under absolute maximum ratings, I see…

  • Resolved

  • 9 months ago
  • Logic
  • Logic forum
Answered

• SN74LVT125: SN74LVTH125のバスホールド回路の違い

  

  Okutsu

  Resolved

  Part Number: SN74LVT125 Hi, The App note says 'All newly developed bus-interface device inputs have a bus-hold circuit.'. Is this only for AXC and AXCH? The LVT already has a bus hold circuit. Is that of LVTH another newly designed circuit? Is…

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74LVTH125: Active bus-hold circuitry clarification.

  

  ArTzy

  Resolved

  Part Number: SN74LVTH125 Other Parts Discussed in Thread: SN74LV4T125 , , SN74LV125 Hi Experts, Good day. Due to supply issue, client would have to choose SN74LVTH125 as replacement for SN74LV4T125. They are only using the part as a translator from 5V to…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74LVTH125: the difference between the SN74LVTH125 and SN74LVT125

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: SN74LVTH125 Other Parts Discussed in Thread: SN74LVT125 , Hi team, Could you pleas share the difference between the SN74LVTH125 and SN74LVT125? Thanks.

  • over 2 years ago
  • Logic
  • Logic forum

• SN74LVTH125: bandwidth

  

  [FAE] Andrew Wang

  TI Thinks Resolved

  Part Number: SN74LVTH125 Other Parts Discussed in Thread: SN74LVTH574 Hi Team, What is bandwidth of this device? Thanks! Andrew

  • over 2 years ago
  • Logic
  • Logic forum

• SN74LVTH125: SN74LVTH125RGY

  

  Sangeetha Venkiteswaran

  TI Thinks Resolved

  Part Number: SN74LVTH125 Other Parts Discussed in Thread: TINA-TI When i tried to create the testbench using Pspice model of the same part in cadence virtuoso( OE tied to GND and Output tied to VCC through pull up resistor), input itself somehow getting…

  • over 2 years ago
  • Logic
  • Logic forum

• SN74LVTH125: Parallel buffers to drive 50-ohm load

  

  Steven Thomas1

  TI Thinks Resolved

  Part Number: SN74LVTH125 The part is SN74LVTH125PW The buffer IC is driven by 3.3V, the Iout is 32mA. Can I put two of these buffers in parallel to increase output current for driving 50-ohm load (scope input)? 32mA * 2 buffers = 64mA 64mA * 50 = 3.2…

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• SN74LVTH125: Bypass Buffer

  

  Alonso

  Resolved

  Part Number: SN74LVTH125 The input/Ouput net name of one of the Quadruple Buffers was mistakenly name the same causing the input/output of that buffer to be shorted together. Can the buffer be bypass and still be used (not as a buffer just bypass) just…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum
Answered

• SN74LVTH125: how to determine the value of pullup resister for OE pin?

  

  TSUTOMU HATTORI

  Resolved

  Part Number: SN74LVTH125 Dear support team, Could you please give some advice to determine the value of pullup resister for OE pin of SN74LVTH125? On the datasheet of the device, it is said that"The minimum value of the resistor is determined by the…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.