Search tips
Showing 53 results View by: Thread Post Sort by
    Answered

  • TAS5634: Relation ship between PVDD and GVDD

    Resolved
    Part Number: TAS5634 Other Parts Discussed in Thread: TAS5614LA , TAS5614 Hello Expert, I'd like to confirm about whether we can use this device with case that GVDD voltage is higher than PVDD voltage. As far as my understanding, there isn't any limitation…
    • Resolved
    • Answered

  • TAS5634: 5936

    Resolved
    Part Number: TAS5634 hello, Our company has a project to design a class D amplifier, and we have some candidates IC, we would like to simulate the performance of the TAS5634. Would you give us some proper advice to implement this idea, hope to get…
    • Resolved

  • TAS5634: clipping

    TI Thinks Resolved
    Part Number: TAS5634 Hi all, I have a question for you. TAS5634DDV is sourced by 60 V. 1 kHz output signal. When voltage on output signal is above 90 V, then amplifier started clipping. It means, that signal is over 1 % THD and that is the reason, why…
    • Answered

  • TAS5634: Are 4 inductors recommended for PBTL?

    Resolved
    Part Number: TAS5634 Hello, I am looking to implement a 250W RMS in to 4Ω in PBTL. In the TAS5634 data sheet the Typical PBTL config (Fig 29) shows the use of 4 inductors, one each for OUTA,B,C,D. Is this required to prevent over current issues, and cross…
    • Resolved
    • Answered

  • TAS5634: Need Power Stages to Support 400W at 2ohm PBTL / 200W at 4ohm BTL

    Resolved
    Part Number: TAS5634 Hi Sirs, Do we have a power stage to support load conditions of 400W, 1%THD+N at 2ohm PBTL and 200W, 1% THD+N at 4ohm BTL? The TAS5634 can achieve 400W at 3ohm PBTL and 200W at 6ohm BTL which cannot meet customer's requirements.…
    • Resolved

  • TAS5634: TAS5634 BTL 4 ohm speaker availability

    TI Thinks Resolved
    Part Number: TAS5634 Hi! My customer is designing Audio Power Amp using the TAS5634. The specifications that the customer wants to set are PVDD 58V, 180W, THD 1%, 8ohm. But the customer wants to use a speaker that drives 4 ohms. My customers have not yet…

  • TAS5634

    TI Thinks Resolved
    Other Parts Discussed in Thread: TAS5634 Dear TI Can I use the TAS5634 for BTL output mode, the power is 2*100W, can the load be two 4 ohm speakers? Because I see the specification BTL mode is only 8 ohms and 6 ohms.

  • TAS5624A: TAS5624 Power output

    TI Thinks Resolved
    Part Number: TAS5624A Other Parts Discussed in Thread: TAS5634 Hi, My current Amplifier configuration is TAS5534 + TAS5634 (2xSE + 1BTL). For the SE channel, the power output at 10% THD not able to reach 110W (around 106W). can the modulation index helps…

  • RE: TAS5634EVM: Not able to play audio with samplerates >48kHz from any source

    Hi Andreas I'm sorry the USB or SPIDF port on the EVM don't support to output all kinds of sample rate. If you want to test with different sample rate of TAS5634, it is suggested to send in I2S signal directly to the input pins of our device TAS5634…
    • Answered

  • TAS5558: Reduce latency and improve EMI

    Resolved
    Part Number: TAS5558 Other Parts Discussed in Thread: TAS5634 Hi, I'm working on an amplifier which is digitally sourced via I2S. As pwm interface I use the TAS5558. The amps are 4 pieces of TAS5634 in PBTL. I have a few questions concerning both devices…
    • Resolved

Didn't find what you are looking for? Post a new question.