The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.



Search tips
Showing 193 results View by: Thread Post Sort by
    Answered

  • TAS6584-Q1: Two TAS6584-Q1 over single I2S

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Please find below image, please let us know if following connection can be made in order to connect Two TAS6584-Q1 Audio Amplifiers with SOC. On SOC side we have only one I2S available for Amplifier and we want…
    • Resolved
    • Answered

  • TAS6584-Q1: About power up sequence order

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Hi team, In the datasheet, it is only written the order for VBAT/PVDD/DVDD, PD and STBY. But do we also have any recommendation on the order for VBAT, PVDD and DVDD? Can it be any order if PD is pulled low? Re…
    • Resolved
    • Answered

  • TAS6584-Q1: Gain Compensation Biquad Coefficient Writing

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Good Morning! I am looking for a register map or the gain compensation biquads. I cannot seem to find it anywhere, is it possible to obtain that information so I can change these filter values manually? Thank you…
    • Resolved
    • Answered

  • TAS6584-Q1: TAS6584-Q1

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Hi team, I need the complete Datasheet from TAS6584-Q1 and the Altium-Design. Thank you Mahmoud
    • Resolved
    • Answered

  • TAS6584-Q1: Output Capacitor Type: Film or Ceramic?

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Hello, I am wondering if there is a recommendation for the type of capacitor used in the output LC filter. I see in the EVM that ceramic SMT capacitors are used. I am wondering if it is OK to use through hole film…
    • Resolved
    • Answered

  • TAS6584-Q1: How to ask a private question.

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Thanks for support. Would you share your mailing list for sending email because I would like to ask questions with may confidential information? Best regards.
    • Resolved
    • Answered

  • TAS6584-Q1: Car Audio Amplifier. Gain Tuning with DD1 Using Open Load.

    Resolved
    Part Number: TAS6584-Q1 Tool/software: Good Afternoon. An interesting use case has come up during the development of a car audio amplifier. Often amplifier installer technicians use something called a DD1 to measure the amount of distortion on an amplifiers…
    • Resolved
    • Answered

  • TAS6584-Q1: Thermal pad ground connection

    Resolved
    Part Number: TAS6584-Q1 Tool/software: What is a proper way, to realize chassis cooling for the TAS6584? According to the datasheet Table 5-1, the thermal pad is connected to ground. Paragraph 11.1.3 states: "Heat-sink mounting screws, E, should be…
    • Resolved
    • Answered

  • TAS6584-Q1: Regarding Inductor values ​​for LPF design.

    Resolved
    Part Number: TAS6584-Q1 Tool/software: The recommended inductor value for a single-stage LPF when the switching frequency is less than 1MHz is 10uH. If the inductor combined with 1uF is reduced from 10uH to 4.7uH, is there anything I should be careful…
    • Resolved
    • Answered

  • TAS6584-Q1: How/where to connect regulator bypass pins

    Resolved
    Part Number: TAS6584-Q1 Other Parts Discussed in Thread: TIDA-020033 Tool/software: Shall the pins DVDD_RET[2], PLL_RET[64], VREG_RET[15] be connected to the GND-plane on the PCB? In the datasheet example schematics Figure 9-1 VREG_RET is connect to GND…
    • Resolved

Didn't find what you are looking for? Post a new question.