Search tips
Showing 277 results View by: Thread Post Sort by

  • TDC7201-ZAX-EVM: TDC7201-ZAX-EVM: LabVIEW GUI Source VI

    TI Thinks Resolved
    Part Number: TDC7201-ZAX-EVM Tool/software: Now I am going to make a test program with TDC7201-ZAX-EVM using labview program, Can you send me the TDC720xEVM GUI source VI? Thank you Best Regards, Woojin Shin
    • Answered

  • TDC7201: What happens with multiple START pulses?

    Resolved
    Part Number: TDC7201 Tool/software: We are attempting to utilize the TDC7201 as a combination pulse width and frequency sensor. We have connected the START and STOP signals together. For pulse width measurement, we configure it to look for 1 stop signal…
    • Resolved
    • Answered

  • TDC7201: Can TDC7201 be used for Luminometer?

    Resolved
    Part Number: TDC7201 Other Parts Discussed in Thread: OPT4001 Tool/software: Hello guys, One of my customers is about to start designing Luminometer. Do you have any reference design or application note for Luminometer? And do you have any TI device which…
    • Resolved
    • Answered

  • TDC7201: INTBx sometimes cannot fall

    Resolved
    Part Number: TDC7201 Tool/software: Hi, Supporter, We encountered the following waveform while using the TDC7201. We are measuring in MODE 1. The Start input uses the same signal as the trigger signal (S1), while the Stop signal receives another signal…
    • Resolved

  • TDC7201: Regarding the timing of data capture in SPI

    TI Thinks Resolved
    Part Number: TDC7201 Tool/software: Hi, support The text in the image states that the DIN: SCLK rising edge, DOUTx: SCLK falling edge. Is this referring to the setup time? Could you please provide a more detailed explanation to help me understand this…

  • TDC7201-ZAX-EVM: Issue in stability of Output in GUI after averaging

    Part Number: TDC7201-ZAX-EVM Other Parts Discussed in Thread: TDC7201 Tool/software: Hii, I just want to know that how can i get rid of the fluctuation output while setting up highest averaging cycle or even to the centre (CONFIG2 Register) in GUI of TDC7201…

  • TDC7201: Why can't the repeated measurements of the count value for TIME1 at a fixed point be the same or within a difference of one calculated value?

    Part Number: TDC7201 Tool/software: Hi, support We know that each measurement provides LSB and TIME1, and TOF is the product of LSB and TIME1.Please refer to Figure 1. This is the STOP signal, with a variation of about 456.8 ps. We expect the difference…

  • TDC7201-ZAX-EVM: TDC7201-ZAX-EVM

    Part Number: TDC7201-ZAX-EVM Other Parts Discussed in Thread: MSP430F5529 , I have a TDC7201-ZAX-EVM which I attached to a MSP430F5529 Launch pad to test out. I used the LabView based GUI and followed the instructions with the TDC7201-ZAX-EVM on how to connect…
    • Answered

  • TDC7201-ZAX-EVM: TDC7201-ZAX-EVM LIDAR START from LMG1020EVM

    Resolved
    Part Number: TDC7201-ZAX-EVM Other Parts Discussed in Thread: LMG1020 , TDC7201 Hi there, Application: laser rangefinder Demo Module using TDC7201-ZAX-EVM and LMG1020EVM Question 1: how to connect a LIDAR START (or laser on) signal from LMG1020EVM board…
    • Resolved

  • TDC7201: TDC7201 minimum pulse width requirement

    TI Thinks Resolved
    Part Number: TDC7201 Can TDC7201 work efficiently with Pulse width of 1ns to 4ns ?

Didn't find what you are looking for? Post a new question.