Search tips
Showing 23 results View by: Thread Post Sort by

  • TIDA-00570: Evaluation module pattern capacity frequency and quantity

    TI Thinks Resolved
    Part Number: TIDA-00570 Other Parts Discussed in Thread: DLPC910 , DLP9000X , DLPC900 , DLP9000 Good morning, We want to manufacture the TIDA-00570 test module, but we want to be sure that this will allow us to send at least 10000 patterns to at least 1Khz…
    • Answered

  • RE: DLPC910: DLPC910

    Resolved
    Hello again Moshe, Good to hear from you. 1. Does the DLPC910 has power up and power down requirements? The data sheet has very little regarding any power up sequencing. There is a DLPC910 reference design that uses the output of some regulators to enable…

  • DLPC910: PWR_FLOAT pin connection

    TI Thinks Resolved
    Part Number: DLPC910 Other Parts Discussed in Thread: TIDA-00570 , DLPC410 Hi Designing with the DLPC910. looking at the datasheet (DLPS064D – SEPTEMBER 2015 – REVISED SEPTEMBER 2020". for PWR_FLOAT pin, it is stated that " Park…
    • Answered

  • DLPC910: TIDA-00570 High Speed DLP Sub-system DLPC910 Main Board

    Resolved
    Part Number: DLPC910 Other Parts Discussed in Thread: TIDA-00570 , In the schematic of Evaluation kit "TIDA-00570 High Speed DLP Sub-system DLPC910 Main Board" drawing № 2514435 there are some pins used at DLPC910, which in Datasheet are classified as …
    • Resolved
    • Answered

  • RE: DLP9000X: DLP9000X EVB

    Resolved
    Moshe, The circuit you are referring to help ensure the proper power-down of the DMD voltages. Voffset, Vreset, and Vbias ("Vorb") need to power down before Vcc. The power-down sequence is quite important. Regarding this question/comment: >…
    • Answered

  • DLPC900: DLPC900 DMD Controller 1-bit Binary Pattern Capacity and Limitations

    Resolved
    Part Number: DLPC900 Other Parts Discussed in Thread: DLPC910 , TIDA-00570 , Hello, I’m currently working with the DLi6500 development kit, and I noticed the memory capacity of the kit caps off at 400 1-bit binary patterns. Is it safe to assume the 48MB…
    • Resolved
    • Answered

  • DLPC910: LVDS input termination (Datasheet Rev D)

    Resolved
    Part Number: DLPC910 Hello, I have noticed the DLPC910 data sheet update to revision D from Sep 28th 2020. It states "Updated Description section for DDC_DCLK_(A,B,C,D)_DP(N,P), DDC_DIN_(A,B,C,D)(1-15)_DP(N,P), and DVALID_(A,B,C,D)_DP(N,P) from …
    • Resolved

  • WEBENCH® Tools/DLP9500: ECP signal can go high

    TI Thinks Resolved
    Part Number: DLP9500 Other Parts Discussed in Thread: DLPC910 , DLPR910 , TIDA-00570 Tool/software: WEBENCH® Design Tools Now, the ECP signal can go high. And VLED0 has the heart beat signal. However, the VLED1 cann't go high. And DLPC910's I2C has no…

  • RE: DLP9000X: Interface details of DLP9000X

    Dear Fizix, I agree with you and understood that DMD DLP9000X should be used with DLPC9000. To understand the operation of these devices, I need some more information I have seen TI reference design document named TIDA-00570 High Speed DLP Sub-system…
    • Answered

  • TPS65145: TPS65145 question about the cause of VBAIS voltage becoming 8V?

    Resolved
    Part Number: TPS65145 Other Parts Discussed in Thread: TIDA-00570 Dear support member, I have a question. From the circuit diagram below I made a board of TPS65145. www.ti.com/.../TIDA-00570 TIDA-00570_2514439b_HI-SPEED_WQXGA_DMD_BOARD_ESD.pdf （Situation…
    • Resolved

Didn't find what you are looking for? Post a new question.