Search tips
Showing 112 results View by: Thread Post Sort by
    Answered

  • TIDA-010042: TIDA-010042: Can I use the same hardware for a 29V lithium battery?

    Resolved
    Part Number: TIDA-010042 Hello, I am planning to add an MPPT charge controller to my current PCB project and I intend to use the TIDA-010042 as my reference design. The TIDA-010042 meets most of my requirements for input voltage and output current…
    • Resolved

  • TIDA-010042: TIDA-010042 Software

    Part Number: TIDA-010042 Hello, I have reviewed your TIDA-010042 product. The software file is located at the bottom of the site: "TIDA-010042-E3.zip — 232 K". Would compiling this file directly with your program work? If this isn't a pre-compiled file…

  • TIDA-010042: TIDA-010042 Does not enter the correct charging states + No load output

    Part Number: TIDA-010042 Hello, I am debugging the TIDA-010042 MPPT PCB in combination with the TIDA-010042 Software (TIDCFD5), but it does not seem to function as expected. During runtime, no error fault LEDs turn on, and nothing out of the ordinary…

  • TIDA-010042: TIDA-010042 MOSFET BASED DESIGN- Is there any issue if I test MPPT code with DC Power supply

    Part Number: TIDA-010042 Other Parts Discussed in Thread: MSP430F5132 Tool/software: Hi, I have tested TIDA-010042 with a meanwell DC power supply. Its maximum current is 30A.When I turn on charge controller with CC limit of 20A, immediately my high…
    • Answered

  • TIDA-010042: TIDA-010042 MOSFET BASED DESIGN INPUT AND OUTPUT CAPACITANCE

    Resolved
    Part Number: TIDA-010042 Tool/software: Hi, Is there any particular reason for using large value bulk capacitor at the input(2 x 1200uF) and output (1 x 1000uF)of TIDA-010042 mosfet based reference design.What happens if I reduce these values. Regards…
    • Resolved
    • Answered

  • TIDA-010042: DCM MODE IN TIDA-010042

    Resolved
    Part Number: TIDA-010042 Tool/software: Hi, I want to know how TI choosen the DEM mode current in TIDA-010042 Mosfet based reference design. According to theory we should go to DEM Mode when the output current goes below or equal to critical current…
    • Resolved

  • TIDA-010042: TIDA-010042 Board availability to purchase

    Part Number: TIDA-010042 Tool/software: Hello, I'm interested in a design based on your TIDA-010042 and we want to use the board for the firwmare development but I can't find it to purchase. Is this board available to purchase instead manufacture…

  • TIDA-010042: One phase of interleaved buck converter is getting heated than other in tida-010042 MOSFET based design

    Part Number: TIDA-010042 Tool/software: Hi, In my tida-010042 MOSFET based design, one phase of interleaved is getting heated than other phase.I assume it may be due to current imbalance between two phases.When I am adjusting the duty of two phases…

  • TIDA-010042: Lower buck threshold value in TIDA-010042 mosfet based design

    Part Number: TIDA-010042 Tool/software: Hi, In the reference code, buck lower threshold is set as 400.Is there any issue for going below this value.How TI chosen this value. Will it cause boosting effect or any other issue, if I start the buck from…

  • TIDA-010042: LMG2100R026 burned

    Part Number: TIDA-010042 Other Parts Discussed in Thread: LMG2100R026 Tool/software: Hi, I ordered two TIDA-010042 MPPT boards through JLCPCB and began testing them with an electronic load using the latest firmware. Initial results were promising: Constant…

Didn't find what you are looking for? Post a new question.