Search tips
Showing 41 results View by: Thread Post Sort by

  • TIDA-01471: Source code to read sensor value?

    TI Thinks Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: ADS127L01 Dear Ahmad, I am using the TIDA-01471 circuit to read an accelerometer with model (805). But I have a problem by reading the sensor valus via SPI interface. I'm trying to read these…
    • Answered

  • TIDA-01471: Requesting customization of board layout

    Resolved
    Part Number: TIDA-01471 Hello, I have a question regarding above-mentioned TIDA board. Is it possible to get a small customization of that board? In particular I need the TP7 output as an output pin. Kind regards, Minh
    • Resolved
    • Answered

  • TIDA-01471: Synchronize multiple IEPE Interfaces

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: ADS127L01 , ADS1274 , ADS1278 Hello, we want to use more than one TIDA-01471 to read multiple IEPE sensors simultaneously. At the moment we have six boards connected to the Controller board and…
    • Resolved
    • Answered

  • TIDA-01471: Some questions about 4-channel vibration interface schematic

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: ADS1274 , HI TI, I need to make a board that can collect four channels of vibration signals. The vibration sensor is uniaxial and 0.1~12000Hz with IEPE/ICP interface. I use STM32F767 as the…
    • Resolved

  • RE: TIDA-01471: about 4 channels SCH IEPE

    Another important point: - you are using 5V AVDD, means your common mode is 2.5V. that matches your reference which is 2.5V. then your full scale input is -2.5V to +2.5V. you are powering the THS with 5V. So far so good, your THS should generate +2…
    • Answered

  • TIDA-01471: Some questions about reference design

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: REF3425 , REF6225 Dear Ahmed, First of all, thanks for your work on this reference design and for answering questions on this forum. It's difficult to overestimate you help. I have some more…
    • Resolved
    • Answered

  • TIDA-01471: Multiplexers and current source based on TLV431BQ

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: MUX36S08 , TMUX6104 Dear Ahmed, I have two questions related to this reference design. 1. In this forum thread , you mentioned the preferred multiplexer for the current source: MUX36xxx or MUX61xxx…
    • Resolved
    • Answered

  • TIDA-01471: 8-channel IEPE vibration sensor DAQ

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: OMAP-L138 , , ADS1274 , REF6225 , REF3425 , ADS127L01 , ADS8900B , ADS1278 , TINA-TI Dear Ahmed, I'm planning to implement an IEPE Sensor DAQ with 8-channels based on TIDA-01471 reference design…
    • Resolved
    • Answered

  • TIDA-01471: IEPE Vibration Sensor Interface

    Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: XTR111 , TLV431 Hi Texas, I have implemented the attached circuit, and the voltages shown have been obtained. What is the error?. VCC24 = 24V AVDD = 3.3V IEPE.docx Thanks,
    • Resolved

  • TIDA-01471: ADC output decreases with increasing frequency

    TI Thinks Resolved
    Part Number: TIDA-01471 Other Parts Discussed in Thread: ADS127L01 Hello, We are evaluating some samples of the TIDA-01471 and get some confusing output we cannot explain. Some plots and the used jumper settings are shown in the attached .pdf document…

Didn't find what you are looking for? Post a new question.