Search tips
Showing 18 results View by: Thread Post Sort by
    Answered

  • TIDA-060025:Can you please tell me which LDs and PDs can test TIDA-060025?

    Resolved
    Part Number: TIDA-060025 Hello! I would like to use the TIDA-060025 system to test LIDAR. Can you please tell me which LDs and PDs can test TIDA-060025? I have never seen a 4pins LD as it is not my area of expertise. Thanks for reading my question. Yu…
    • Resolved

  • TIDA-060025: Driver board for 145W LiDar

    Part Number: TIDA-060025 Dear team, Could you please review below spec requirements for LiDar application, and share with me some related technical information to me customer? Peak output power (max): 145W If (max): 40A Pulse width: 10~100ns Laser wavelength…
    • Answered

  • TIDA-060025: OPA858 noise calculation in TIDA-060025

    Resolved
    Part Number: TIDA-060025 Other Parts Discussed in Thread: OPA858 I have a TIA question concerning a noise calculation in the TIDA-060025 reference design document. I am calculating a different noise current value than the reference design indicates…
    • Resolved

  • TIDA-060025: Missing Firmware version 2.08 for MSP430F5529 EVM to cooperate with TIDA-060025 EVM

    TI Thinks Resolved
    Part Number: TIDA-060025 Other Parts Discussed in Thread: TDC7201-ZAX-EVM As far as I saw in the user guide of TIDA-060025 (FW version box on the top right of Figure 19, page 15), the firmware for MSP430F5529EVM that was used is 2.08. But I can not find…

  • TIDA-060025: Cannot update Firmware for MSP430F5529 EVM in reference design TIDA-060025 EVM

    TI Thinks Resolved
    Part Number: TIDA-060025 Other Parts Discussed in Thread: TDC7201 , MSP430F5529 , TDC7200 , MSP430WARE Hi everyone, I am working on TIDA-060025 Ref Design. I am having trouble with upgrading firmware (attached below) that engineer from TI gave me to MSPF5529…
    • Answered

  • TIDA-060025: Comparator to TDC Voltage

    Resolved
    Part Number: TIDA-060025 Other Parts Discussed in Thread: TDC7201 Hello! I noticed that the comparator output is 5V and it goes to a stop pin on the TDC7201. According to the TDC7201 the max voltage on the pin is 3.6V. Isn't the comparator in this design…
    • Resolved
    • Answered

  • RE: TIDA-060025: Amplifier design for Lidar

    Resolved
    Hello Sara, I am really glad that the TIDA-060025 reference design is helping with designing your application! I am assuming you are getting a 25mV signal out of the OPA858. Are you using the same or similar key system specifications as the TIDA-060025…

  • TIDA-060025: EVM board built is not detected by TDC-7201 GUI program

    Part Number: TIDA-060025 Other Parts Discussed in Thread: MSP-EXP430F5529LP , , TDC7201-ZAX-EVM , TDC7201 Hi, sir; We have built two TIDA-060025 EVMs and put togeter with MSP-EXP430F5529LP module. We downladed firmware and TDC-7201 GUI progrmam, and tested…

  • TIDA-060025: Follow up to lidar design question-comparator/preamplifier

    Part Number: TIDA-060025 Other Parts Discussed in Thread: TINA-TI , OPA858 , LM158 , TLV3501 , OPA836 , LM7171 , LM6171 Hello again, My team is still working on this particular design and it has been suggested that we should add in an op amp amplifier to increase…

  • TIDA-060025: Lidar amplifier design followup question-power

    TI Thinks Resolved
    Part Number: TIDA-060025 Other Parts Discussed in Thread: TDC7201 , TLV3501 , (This is a follow on question to the one I posted under "Amplifier design for lidar") My team is designing a lidar using the reference design but with our own laser diode…

Didn't find what you are looking for? Post a new question.