Search tips
Showing 1,005 results View by: Thread Post Sort by

  • CC2652P: LP-CC2652RB for development of CC2652P

    TI Thinks Resolved
    Part Number: CC2652P Other Parts Discussed in Thread: CC2652RB , LP-CC2652RB , LAUNCHXL-CC1352P Hi, I have launchpad for CC2652RB .My final product is based on CC2652P as ZNP. I am using is simplelink_cc13x2_26x2_sdk_4_30_00_54.Can i use LP-CC2652RB…

  • RE: CC2530: Simple binding of a switch and a light

    The example takes the address of the first device since it is a proof of concept demonstration only. You should further develop your application in whichever way you determine necessary. You can send a ZDP_BindReq for your application or use ZDO_BIND_REQ…
    • Answered

  • RE: Launchpad as a coordinator + router

    Resolved
    You can run ZNP on CC2652 launchpad so host can configure it as coordinator or router according to your application requirements.
    • Answered

  • RE: LAUNCHXL-CC26X2R1: Re-start zigbeeHAgw (& start_application) scripts makes ZED cannot join network.

    Resolved
    A soft reset will cause a software reset command of the ZNP firmware, whereas restarting the zigbeeHAgw script only affects the host software operation. You would use the srvwrapper version as RPC_SYS_PROTOBUF is commonly referenced by other source…

  • RE: CC2530-CC2591EM-RD: Unable to control end device

    Since you are using ZNP, I agree with Ryan that you should check if the ZNP device still respond to MT commands from the host first.

  • CC1352P: CC2652 ZNP UART communication with RaspberryPi

    TI Thinks Resolved
    Part Number: CC1352P Other Parts Discussed in Thread: CC2538 , SYSCONFIG , , Hello Community, I am working on CC1352P-2 launch pad. using the znp example code. I would like to replace the CC2538 ZNP device with the CC1352P-2 launch pad to interface…
    • Answered

  • CC2652R: ZNP on cc2652r1F

    Resolved
    Part Number: CC2652R Other Parts Discussed in Thread: CC2650 , LAUNCHXL-CC26X2R1 , CC2592 , CC2652P , , SIMPLELINK-CC13X2-26X2-SDK , SMARTRFTM-STUDIO I try to to start ZNP- project on board based on this https://www.ti.com/tool/TIDC-CC2650-CC2592-EMK…
    • Resolved
    • Answered

  • RE: CC2630: enddevice state change from :DEV_NWK_DISC-> DEV_END_DEVICE-->DEV_NWK_ORPHAN-->DEV_NWK_REJOIN-->DEV_NWK_DISC

    Resolved
    my host is the example cmdLine from https://git.ti.com/cgit/znp-host-framework/znp-host-framework
    • Answered

  • RE: CC2652P: How to get the ZNP to auto-start

    Resolved
    We usually use APP_CNF_BDB_START_COMMISSIONING to start coordinator right after host and znp starts.
    • Answered

  • CC1352P: Zigbee Direct Support for the CC1352P

    Resolved
    Part Number: CC1352P Hello Community, I am working on the CC1352P ZNP device with the ZNP Host Framework Application. I am reading some documents regards to Zigbee Direct on the Zigbee Alliance site. connectivity-standards-alliances-zigbee-direct…
    • Resolved

Didn't find what you are looking for? Post a new question.