Search tips
Showing 20 results View by: Thread Post Sort by

  • TL081H: Pin name different

    TI Thinks Resolved
    Part Number: TL081H Tool/software: Hi Team my customer find below IC pin name is different. could you help me check which one is correct? and do you have any plan to fix datasheet? BRs Brian
    • Answered

  • TL081H: Cost effective voltage follower opamp

    Resolved
    Part Number: TL081H Other Parts Discussed in Thread: LM321LV , TLV9001 Tool/software: Hello, We are trying to find a simple 1 channel cost effective voltage follower opamp. We intend to connect a voltage divider to the noninverting input and use…
    • Resolved
    • Answered

  • TL081H: Output Transient Capability

    Resolved
    Part Number: TL081H I have a scenario where the TL081H will be supplied with a 18 VDC single voltage supply (Vss to GND). The output of this device goes to an external connector that is required to meet voltage transient specifications. From an LTSpice…
    • Resolved
    • Answered

  • TL081H: Technical query Regrading OPamp TL081HIDBVR

    Resolved
    Part Number: TL081H Other Parts Discussed in Thread: LM7705 , OPA320 , Hi Taru We have used opamp TL081HIDBVR in our Design. Just a query if this opamp can work with below input voltage range Input at non inverting terminal= 0V to 3.5V SCH…
    • Resolved

  • TL081H: What's the difference?

    TI Thinks Resolved
    Part Number: TL081H Other Parts Discussed in Thread: TL071H , , TL084H , TL082H , TL074H , TL072H What's the major difference between TL081H and TL071H? I'm wired about these two family. Regards Brian W
    • Answered

  • TL081H: Output stage difference from legacy TL081

    Resolved
    Part Number: TL081H Other Parts Discussed in Thread: TL081 , TL084H , TL084 Hello, From datasheet SLOS081M is appears that output swing, especially positive for the new TL081H is close to the rail (500mV). Old TL081 can go only 1.5V from the rails…
    • Resolved
    • Answered

  • TL081H: Does the new CMOS H model have the same JFET source impedance distortion issues the old JFET models did?

    Resolved
    Part Number: TL081H Other Parts Discussed in Thread: TL081 , TL072 , TL072H , OPA1642 , TL052 , , TL082 , TL082H According to this technical note , The old JFET TL072 had increasing distortion with increasing source impedance, which I assume was also…
    • Resolved
    • Answered

  • TL081: TL081C

    Resolved
    Part Number: TL081 Tool/software: Hello Support Team, For the past 20 years, we have used the TL081C in our electronic boards, with the known specifications for VOM max. 13.5V at a supply voltage of +/-15Vsup. We noticed that the VOM value had changed…
    • Resolved
    • Answered

  • TL074: Possibility of oscillation due to failure

    Resolved
    Part Number: TL074 Other Parts Discussed in Thread: TL081H Tool/software: A problem occurred where several TL074IDRs oscillated. I'm investigating whether EOS is the cause, or if there is a problem with the circuit and the oscillation is caused by variations…
    • Resolved
    • Answered

  • LM2904V: High Side Current Sense Output Issue

    Resolved
    Part Number: LM2904V Other Parts Discussed in Thread: OPA990 , TL081H , INA180 Tool/software: Hi TI, I use LM2904V to design a high side current sense circuit. I hand made a circuit and measure it, but output voltage is abnormal at Vbat lower than…
    • Resolved

Didn't find what you are looking for? Post a new question.