Search tips
Showing 80 results View by: Thread Post Sort by

  • RE: Compiler/TL16C752D: TL16C752D linux driver do not work

    Hi Eric , Thanks for your replication, I have successfully added the support for TL16C752D, And I tested with RS232 mode, It works well, But when I change to RS485 mode , I can only send messages( receive side can receive successfully), but can…

  • TL16C752D: Searching TI solution

    Answer Suggested
    Part Number: TL16C752D Other Parts Discussed in Thread: TUSB3410 , MSP430F5508 Hi Team, There is a good new that we could DIN TI product! Customer is looking for "2 UART to single USB" Do we have the solution for this cade? THX
    • Answered

  • TL16C752D: I2C/SMBus to UART receiver/transmitter

    Resolved
    Part Number: TL16C752D Hi, I have a question about TL16C52D this part. I would like to check if TL16C52D can support I2C to UART receiver/transmitter. If not, then does TI have the comparable part to NXP SC16IS752IBS for I2C/SMBus to UART receiver…
    • Resolved

  • TL16C752D: The difference of FCR[7:6] between TL16C752D and TL16C752B

    TI Thinks Resolved
    Part Number: TL16C752D Hello, Could you tell me why the FCR [7: 6] value has changed between TL16C752B and TL16C752D? <TL16C752B> <TL16C752D> Best Regards, Kaede Kudo
    • Answered

  • TL16C752D: Delay from stop to interrupt of TL16C752D and TL16C752B

    Resolved
    Part Number: TL16C752D Hello, I have a question about the contents of the thread below. https://e2e.ti.com/support/interface/f/138/p/542016/2247137 Please tell me about Delay from stop to interrupt. ・TL16C752B: 100[ns] ・TL16C752D: 1[baudrate]…
    • Resolved
    • Answered

  • TL16C752D: Difference between TL16C752B and TL16C752D

    Resolved
    Part Number: TL16C752D Hello E2E, If change the device from TL16C752B to TL16C752D, do we necessary to modify for driver S/W? Regards, ACGUY
    • Resolved

  • TL16C752D: Can I read and write to Scratch register (SPR, reg addr 0x7)?

    Part Number: TL16C752D I write some data to this register. When I read it back, I always get 0x00. This is after reset, and I have not programmed any other registers yet, so reg address 111 should be SPR. There is no documentation about the SPR register…

  • RE: TL16C752D: About TL16C752D replacing TL16C752B

    Hi Vera, Just closing off this thread in the forum since this discussion has been continued offline via email. Regards, Max

  • TL16C752D: UART connection to TL16C752

    TI Thinks Resolved
    Part Number: TL16C752D Hi All, I have a question about UART connection to TL16C752. I am asking because I have no knowledge of UART. I'm sorry to ask you some basic questions. - What input timing for CD? - What input timing for DSR? - What input…
    • Answered

  • TL16C752D: Not asserting LSR[5]

    Resolved
    Part Number: TL16C752D Hello, LSR[5] is not often asserted after transmitting interrupt with 9600bps rate in spite of IIR = 0xC2(THR interrupt). LSR[5] is asserted in the following condition. - 4800bps rate or waiting 500ns after interrupt or…
    • Resolved

Didn't find what you are looking for? Post a new question.