Search tips
Showing 26 results View by: Thread Post Sort by
    Answered

  • TL7700-SEP: TL7700-SEP Filtered Sense

    Resolved
    Part Number: TL7700-SEP Tool/software: Hello - I am using the TL7700-SEP as a supply supervisor, as shown in Figure 9-1 of the datasheet. I'd like to add a filter capacitor from SENSE to ground (i.e. in parallel with the 30k R2 resistor). I'd think this…
    • Resolved

  • TPS3762-Q1: TPS3762-Q1,TPS3842 ,TPS3842-Q1 ,TL7700-SEP

    TI Thinks Resolved
    Part Number: TPS3762-Q1 Other Parts Discussed in Thread: TPS3762 , TL7700-SEP , TPS3842 Tool/software: Hello team!! I can't found the Spice model for the some of the part numbers on the website. Please provide the spice model for the part numbers…

  • TL7700-SEP: Enquiry on Spice Model or Design Guide (One-Shot Latch) for use with TL7700-SEP

    TI Thinks Resolved
    Part Number: TL7700-SEP Hi Team, With reference to this article, customers are planning to design a latched (SENSE) output using the TL7700-SEP https://www.ti.com/lit/ab/snva836a/snva836a.pdf?ts=1715128964834&ref_url=https%253A%252F%252Fwww.google…
    • Answered

  • TL7700-SEP:データシートFigure9-1の抵抗値、240kと30kは正しいでしょうか

    Resolved
    Part Number: TL7700-SEP Tool/software: 式(7)でVs'=4.5V、式(5)でVhys=0.6Vとなる抵抗値ですので、 　　　　(1)5V電源が4.5Vで、RESETがhigh=>low 　　　　(2)5V電源が5.1Vで、RESETがlow=>high という動作になるものと理解しました。 ■質問 (2)の動作は正しいでしょうか。 5V電源の監視で、5.1Vを観測することは通常はありませんので、 リセット解除できないことにならないでしょうか。
    • Resolved

  • TL7700-SEP: SET Reset Pulsewidth

    TI Thinks Resolved
    Part Number: TL7700-SEP Tool/software: According to the SEL Radiation Report, there were SETs resulting in up to 140us reset pulses. This is with the circuit configured for 51us nominal reset pulse. If the reset pulse is configured for longer pulses,…

  • TL7700-SEP: TL7700CPWR vs TL7700CMPWPSEP

    TI Thinks Resolved
    Part Number: TL7700-SEP Other Parts Discussed in Thread: TL7700 Hi team, I want to use TL7700CMPWPSEP as a voltage supervisor in a power circuit and I made a small evaluation board for POC. Can I use TL7700CPWR for my evaluation? Is there a significant…
    • Answered

  • TL7700-SEP: LT7700-SEP PSpice Model

    Resolved
    Part Number: TL7700-SEP Hello There, I need run some PSpice simulations and I am looking for the PSpice model for the TL700-SEP supervisory circuit. I already have OrCAD PSpice installed and only need the PSpice model for this device. Can someone…
    • Resolved

  • TL7700-SEP: Statistical Process Control information or reliability information from lot to lot for TI Enhanced Plastic Line

    TI Thinks Resolved
    Part Number: TL7700-SEP Tool/software: Hello. I am looking for Statistical Process Control information or any information on reliability from lot to lot for your Enhanced Plastic line. I am trying to find evidence to compare this line to something like…

  • TL7700-SEP: RAD-HARD negative voltage supervisors ?

    TI Thinks Resolved
    Part Number: TL7700-SEP I am trying to do a negative power supervisor, but as the TL7700-SEP meaning in a RAD-HARD environment. Is there any RAD-HARD negative voltage supervisors on the market and if not how would You hook up the TL7700- SEP to sense…
    • Answered

  • TL7700-SEP: Maximum current rate through the BJT in the RESET pin.

    Resolved
    Part Number: TL7700-SEP Hi, I'm looking to use TL7700-SEP RESET pin as a switch for another circuit, but I need the current (from the RESET Pin to the GND) to be 8mA up to 25mA. Is it possible? Thanks, Moral.
    • Resolved

Didn't find what you are looking for? Post a new question.