Search tips
Showing 149 results View by: Thread Post Sort by

  • RE: TLK105L: Problem with PoE

    Hi,Darwin I think the problem in TLK105L, yesterday I changed(resolder) it on DP83822IF recommended on TI website. I try to work with it like I work with TLK105L and I didn't see same problem. Like I said the problem in TLK...you should check it...…

  • RE: TLK105L: Hardware reset

    Hello Vikram, We will design with the hardware reset the next revise board using DP83826. Why some TLK105L work even the clock delayed ? About 50% of TLK105 work, the other 50% does not. BestRegards, Abe

  • TLK105L: About LED_CFG

    TI Thinks Resolved
    Part Number: TLK105L Hi team, Could you tell me about LED_CFG (BIT5 or PIN 27)? When the hard trap and register setting are different modes, How does it behave? Thanks.
    • Answered

  • TLK105L: Need crystal reference part number and load capacitor value for "TLK105L"

    Resolved
    Part Number: TLK105L Other Parts Discussed in Thread: TLK105 , TIDA-00928 Hai, Thank you for showing interest on my post. I am working on "TLK105L" Ethernet Phy chip and got some reference designs to start my design. But unfortunately i could not see…
    • Resolved
    • Answered

  • TLK105L: Make sure couple of things

    Resolved
    Part Number: TLK105L Hi Application specialists Customer found TLK105LRHB status was changed to NRND and give us couple of question regarding TLK105LRHB and DP83822IRHB. When do we supply this device? if its possible pls give us forecasts. Do we have…
    • Resolved
    • Answered

  • TLK105L: About Auto-MDIX

    Resolved
    Part Number: TLK105L Other Parts Discussed in Thread: DP83630 Hi all, Does TLK105L's Auto-MDIX behave in the same way as DP83630's Auto-crossover when in Force mode? If it is fixed to 100Base-Tx, will the polarity be corrected? Regards, Toshi
    • Resolved

  • TLK105L: Inquiries about Link pulse (Urgent Help/)

    TI Thinks Resolved
    Part Number: TLK105L Hello Team., I have 5 inquiries about TLK105L as below. Could you advise me ? I hope to have your feedback by the end of today July26th.... (1) Is the polarity of FLP NAGATIVE if the Polarity Swap: of Control Register 3 (CR3) is set…

  • TLK105L: AM437x and TLK105L, which Bob Smith Termination to use?

    TI Thinks Resolved
    Part Number: TLK105L Hello team, I'm working on a project based on the AM437x which has the EtherCAT interface and supports also EtherCAT-P which in our case is implemented by using two PHY TLK105L. I would like to know: - Which Bob Smith configuration…

  • TLK105L: Which device insteal of TLK105LRHB ?

    TI Thinks Resolved
    Part Number: TLK105L Dear all When I check the TLK105LRHB datasheet from TI official website, find the device is NRND status. Could you tell me that is there update device for TLK105LRHB, which can be used to industrial ? Thanks a lot.

  • DP83822I: Question on replacing a TLK105L

    TI Thinks Resolved
    Part Number: DP83822I Other Parts Discussed in Thread: TLK105L , TLK105 , TLK106 , TLK106L Several of our designs employ EtherCAT ports using the TI TLK105L PHY. One of the BOM reports ran a board flagged the TLK105L as end of life so our engineer contacted…

Didn't find what you are looking for? Post a new question.