TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 41 results View by: Thread Post Sort by
    Answered
  • TLV3401 Open Drain Truth Table?

    Handi Kartadihardja
    Handi Kartadihardja
    Resolved
    Other Parts Discussed in Thread: TLV3401 , TINA-TI Hi all, I have a question on the truth table for this comparator. If the Input + voltage is bigger than input -, then the output of the comparator is 1. However, since this is an open drain comparator,…
    • Resolved
    • over 9 years ago
    • Amplifiers
    • Amplifiers forum
  • TLV3401 output when comparator not powered

    Handi Kartadihardja
    Handi Kartadihardja
    Other Parts Discussed in Thread: TLV3401 Hi all, I think it is a silly question, but I just want to verify: For TLV3401 comparator, if the IC is not powered, does the output is consistently high (pull-up resistor) since the internal mosfet is not being driven…
    • over 9 years ago
    • Amplifiers
    • Amplifiers forum
  • TLV3401 open-drain pull-up voltage requirements

    Eduardo Rey
    Eduardo Rey
    Other Parts Discussed in Thread: TLV3401 I am using the TLV3401 comparator in a design where I currently have the open drain pull-up voltage set to +3.3V while powering the device with a single +5V supply. This is working properly as it is now but I would…
    • over 9 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: TLV3701: TLV3701 damage cause

    Clemens Ladisch
    Clemens Ladisch
    Resolved
    The 1N750 is a 4.7 V Zener diode. With the 500 Ω resistor from the 15 V supply, it tries to draw a current of 20 mA, which exceeds the TLV3701's absolute maximum rating. Why 500 Ω? What drive strength do you need at Vout? Wouldn't a 2:1 voltage…
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • TLV3401 hysteresis voltage

    Chandrasekaran M
    Chandrasekaran M
    Other Parts Discussed in Thread: TLV3401 Hi I would like to know the hysteresis voltage of TLV3401ID. Can you please help me on that? Thanks, Chandru
    • over 11 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • TIPD111: Hardware "pace" using slope detection circuit work with Vcc as 3.3v instead of 5v: additional questions

    user6529224
    user6529224
    Resolved
    Part Number: TIPD111 Other Parts Discussed in Thread: TLV3401 , TINA-TI , OPA348 , ADS1298 Hello Ryan, I am willing to use the HW pace detection circuit with DVDD=3.3V and bipolar supply for AVDD/AVSS=+/- 2.5V with respect to GND. I have three questions…
    • Resolved
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • RE: LM741: Looking for a Good Op-Amp Suggestion for a pulse detecting with 0.5ms pulse width

    Ron Michallick
    Ron Michallick
    Hello Lakshitha Lathpandura, Welcome to the forums. Your circuit is stressful and harmful to the op amp. I added some protection and changed to a comparator. I'll let the comparator team refine this circuit. TLV3401.TSC
    • over 2 years ago
    • Amplifiers
    • Amplifiers forum
  • LM5116: LM5116: testing on actual board

    Mandar Mahajan89
    Mandar Mahajan89
    TI Thinks Resolved
    Part Number: LM5116 Other Parts Discussed in Thread: TLV3401 , TLV1701 hi , in continuation to the post & schematic shared & the verification & the suggestions by TI , my customer has made the PCB board . below are the testing results : we…
    • over 3 years ago
    • Power management
    • Power management forum
  • RE: TLV7041: Recommend any solution as TLV7041 but input voltage can be more than 7V?

    user4979899
    user4979899
    Please help to check same question for TLV3401 that will it work If the input pins are about 6.5V and VS is 5V? www.ti.com/.../tlv3401.pdf
    • over 3 years ago
    • Amplifiers
    • Amplifiers forum
  • Schmitt trigger schematic and TI Parts survey

    JOHN KUO
    JOHN KUO
    TI Thinks Resolved
    Other Parts Discussed in Thread: TL331 , TLV3401 , TLV1701 Hello TI, Could help us to provide Schmitt trigger schematic for below condition? also, we need you suggestion small package comparetor, thanks!
    • over 3 years ago
    • Amplifiers
    • Amplifiers forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.