• TLV711: TLV7111533DDSER

  

  Billy Parthipan

  TI Thinks Resolved

  Part Number: TLV711 Hi, I am trying to find out/confirm the timing relationship between EN1, 2 and VOUT1, VOUT2. I have a power sequencing requirement and can't have VOUT2 (1.5V) reaching its final value before VOUT1 (3V3) reaching its final value.…

  • over 1 year ago
  • Power management
  • Power management forum

• TLV711: TLV711 dual output current size

  

  Hank Wang

  TI Thinks Resolved

  Part Number: TLV711 May I ask whether the 200mA current of TLV711 is 200mA in two ways or each way can output 200mA? Thank you!

  • over 6 years ago
  • Power management
  • Power management forum
Answered

• TLV711: Use TLV711as single output.

  

  Matt Rad

  Resolved

  Part Number: TLV711 In my application I'm just using only one of the output. What is the TI recommendation for second output(unused) pin connection? Should the unused output float or tie to grand.

  • Resolved

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• RE: TLV711: Is TLV711 made by CMOS or Bipolar

  

  Jason Song

  Resolved

  Hi Sean, TLV711 is with a CMOS; UA78 is with a bipolar process. 1. Do we have same spec like TLV711 and UA78 and made by BJT(bipolar)? To get you to the right device, will you share your application requirements? Like Vin, Vout, load current? It…

  • over 6 years ago
  • Power management
  • Power management forum

• TLV711: Maximum output capacitance

  

  Marcel Schildknecht

  TI Thinks Resolved

  Part Number: TLV711 What is the maximum capacitance that can be connected to the output for stability, or can it be increased without limit? I would connect around 100uF.

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• TLV711: What is the startup time .

  

  user6376681

  Resolved

  Part Number: TLV711 Hi , In the table on page 3, it shows the startup time typically is 100us and define the startup time. In Fig 67-69, it demostrates in VIN/VEN ramp up status and the startup time can be indicated in us unit. It may caused by dropout…

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum

• TLV711: Pull Down Resistor Tolerance

  

  David Mckinney

  TI Thinks Resolved

  Part Number: TLV711 For the 150k ohm pull-down resistor on the TLV7111833DDSER ENx pin(s), can you provide the tolerance of the 150k ohm internal resistor?

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• TLV711: What is the MAX output CAP?

  

  user6376681

  Resolved

  Part Number: TLV711 Other Parts Discussed in Thread: TLV751 , TLV755P I can not find this value on the datasheet. In my design, TLV711 is msut able to drive more than 50uF.

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• TLV711: what's the slew rate on output of LDO (TLV707 and TLV711)

  

  Shaquille Chen

  Resolved

  Part Number: TLV711 Other Parts Discussed in Thread: TLV707 , Hi Team, My customer want to know what's the slew rate of TLV707 and TLV711. Is this able to calculate if the output cap is fixed? How to adjust the slew rate? Thanks Shaq.

  • Resolved

  • over 6 years ago
  • Power management
  • Power management forum

• TLV711: Thermal Information

  

  Mark Philip Felipe

  TI Thinks Resolved

  Part Number: TLV711 I have a customer who is asking for the thermal impedance for TLV7111533DDSER. Junction to case and Junction to ambient. Thank you very much

  • over 6 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.