• TLV740P: Qualification Tests Conditions

  

  Shinichi Yokota

  Part Number: TLV740P Hello, I have some questions about TLV74033PDBVR's qualification tests. JESD22-A108 : What's the operating voltage used for the test JESD22-A108 ? This question refers to the section 4.2.2 Operating Voltage of the JESD22…

  • over 2 years ago
  • Power management
  • Power management forum

• TLV740P: Solderability test condition of TLV74033PDBVR

  

  Kenta Yajima

  TI Thinks Resolved

  Part Number: TLV740P I'd like to knoe what is the test condition of TLV74033PDBVR for Solderability. I expect that this is based on "J-STD-002". Is this right? If so, could you please clrify detail test condition of " J-STD-002"?

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• TLV740P: Question about TLV74033PDBVR max ground current versus ouptut current

  

  Lionel Saurin

  Resolved

  Part Number: TLV740P Hello, Is a graph available about maximum ground current/Output current at 25°C ? The datasheet gives only the nominal.

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum

• TLV740P: TLV74018PDBVR

  

  Ludmila Portnov

  TI Thinks Resolved

  Part Number: TLV740P hi, Please, let us know the min and max T junction of TLV74018PDBVR. We found the few places in Data Sheet with different number: 85deg or 125deg Thanks in advance

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• TLV740P: Footprint not matching - X2SON part showing SOT23 footprint

  

  Vijayasarathy N

  Resolved

  Part Number: TLV740P Hi TI Power Champs Would like to bring to your attention that the footprint for TLV74033PDQNR [X2SON package] is displaying and downloading SOT23-5 pin package, as in below link https://vendor.ultralibrarian.com/TI/embedded…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• TLV740P: short circuit limiter

  

  Stefan Lintner

  Resolved

  Part Number: TLV740P Hi Team, a customer would like to confirm the following: TLV74033PDQNR: they would like to use the 3.3V output version and we will use it with input voltages below 3.3V so to have an output voltage following the input with a difference…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• TLV740P: EN pin is Schmitt trigger input?

  

  Hideki Hayashi1

  TI Thinks Resolved

  Part Number: TLV740P Other Parts Discussed in Thread: TLV743P , , TLV733P Hi team, Do TI LDOs, especially TLV740P, TLV743P, TLV733P, have EN pins with Schmitt trigger input? (=Hysteresis input) Best regards, Hideki

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• TLV740P: Package Drawing

  

  Tamio Yokokura

  Resolved

  Part Number: TLV740P Hi, TLV740P support team, There are not the detail package information in datasheet. Please share Package outline, Example Board Layout and Example Stencil Design with me. Regards, Tamio

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum

• TLV740P: Voltage Drop Out Curve

  

  MattLin

  TI Thinks Resolved

  Part Number: TLV740P Hi Team, Had a question about Figure 6-5 in the datasheet. What is the portion of the curve before linearity in dropout voltage vs. input voltage? It appears like the drop out is higher than the input voltage before the input…

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• TLV740P: Start-up time

  

  Zeming Kong

  Resolved

  Part Number: TLV740P Other Parts Discussed in Thread: TPS7A20 , TLV743P Hi team, From datasheet, the start-up time of TLV740P is 100us(typ.), but from Figure 6-25, it shows a about 700ns start-up time. Could you tell me why the start-up time is different…

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.