Search tips
Showing 23 results View by: Thread Post Sort by

  • TLV766-Q1: Power management forum

    TI Thinks Resolved
    Part Number: TLV766-Q1 We are planning to use TLV766-Q1 (5V fixed version) for our project. It is written in the datasheet that the EN pin has an internal resistance. However our requirement is that initially the IC must be in OFF state, after 2 seconds…
    • Answered

  • TLV766-Q1: Customer question regarding TLV766-Q1 thermal resistance

    Resolved
    Part Number: TLV766-Q1 Hello team I received question from cutomer Question1 In the 6.4 Theemental Information bullet of the data sheet, Each one has a defined thermal resistance, but is this value the typ value or the max value? Question2 What is the…
    • Resolved

  • TLV766-Q1: start up time

    TI Thinks Resolved
    Part Number: TLV766-Q1 Hi team, I would like to control the Vout (set to 0.9V) start up time between 150us to 3ms from VIN=3.3V. This device has typical 500us soft start. Could you advise if this device can meet my requirement over PVT? regards,
    • Answered

  • TLV766-Q1: Constant current LED driver

    Resolved
    Part Number: TLV766-Q1 Other Parts Discussed in Thread: LM317 , Hi Team, Our customer would like to confirm if they can use the TLV766-Q1 as a constant current driver like LM317. Aside from the Output Pulldown function, the internal configuration of the TLV766…
    • Resolved

  • TLV766-Q1: fixed version internal resistors

    TI Thinks Resolved
    Part Number: TLV766-Q1 Other Parts Discussed in Thread: TLV767-Q1 , , TLV767 Hello, from Figure 7-2 in the datasheet I have a doubt about the match between the available output voltages (1.2, 1.8, 3.3, 5.0) and the values/ranges of R1 and R2. It seems…
    • Answered

  • TLV766-Q1: Question about line regulation.

    Resolved
    Part Number: TLV766-Q1 Hello Team, Our customer have some question about line regulation spec. It shows the max is 0.02%/V. Q1. Does the line regulation characteristic of TLV766-Q1 will increase monotonic? (If Vin will increase, Vout will increase as…
    • Resolved

  • TLV766-Q1: With the device off (no IN voltage), will a secondary supply connected to OUT damage the device?

    TI Thinks Resolved
    Part Number: TLV766-Q1 Hi! I would like to know if there need to be additional parts (Schottky diode?) if we expect that a secondary supply may apply voltage to OUT/SNS. For example: 1] The TLV766 may have 12V IN with a fixed output of 3.3V. 2] The 12V…

  • TLV766-Q1: BCI test

    TI Thinks Resolved
    Part Number: TLV766-Q1 Hi team, Customer report there is a output abnormal issue with BCI test. The current injection clamp as shown in below picture's circle that inject interference signals of 1-400MHz, and then there will be AC signal in this section…
    • Answered

  • TLV766-Q1: Pull up resistance of EN pin

    Resolved
    Part Number: TLV766-Q1 Hello Team, Our customer plan to use TLV76601QWDRBRQ1. I think the EN pin has internal pull-up resistor. Can you please let me know the min/typ/max of the pull up resistance? Thanks, Yuta Kurimoto
    • Resolved
    • Answered

  • TLV766-Q1: Question about dropout voltage

    Resolved
    Part Number: TLV766-Q1 Hello Team, I have a question about Dropout voltage(Vdo) I understand if the input voltage is low, the Vout also decrease based on the equation Vdo=Vin-Vout. In this situation, is there any other disadvantage such as noise, power…
    • Resolved

Didn't find what you are looking for? Post a new question.