Search tips
Showing 46 results View by: Thread Post Sort by
    Answered

  • RE: LMV822-N: ESD cell trigger with fast power supply slew rate

    Resolved
    Hello Itoh-san, Maximum recommended supply rise time is rarely documented in data sheets. If this is listed, it means a problem was discovered during device qualification. Long ago qualification plans didn't include this test. Mostly because even older…

  • OPA835: Error in spice model

    Part Number: OPA835 Other Parts Discussed in Thread: OPA2834 , TLV9052 , , TINA-TI Hello, We are working on a circuit where we are evaluating several operational amplifiers, both from TI and other vendors. The devices we have been looking at include the…
    • Answered

  • RE: INA332: Problem with output of INA332. It not followed the reference.

    Resolved
    Hi Marcus, Did you use TLV9052 part with thermal pad? The thermal pad is required to connect to the most negative power rail or V- in a design. For a single supply rail, the thermal pad is required to be connected to ground. If you have other questions…

  • TLV9062: Using Opamps as Comparators

    TI Thinks Resolved
    Part Number: TLV9062 Other Parts Discussed in Thread: TLV9302 , OPA2990 , TLV9042 , TLV9352 , TLV9052 , TLV9152 , OPA2991 , TLV9102 , LM358B , TLV9002 Hello, I was reviewing this E2E post which states that any of these operational amplifiers could also be used…

  • TLV9152: Question for shutdown pin

    TI Thinks Resolved
    Part Number: TLV9152 Other Parts Discussed in Thread: TLV9062 , TLV9052 Hello expert, I have questions for TLV9152S. First, I'd like to confirm about actual logic of shutdown pin. In datasheet's pin function description said it is active-high shutdown…

  • THS4532: Single-Ended to Differential FDA Configuration

    Part Number: THS4532 Other Parts Discussed in Thread: TLV9052 , Hello team, Can you show me the designed values for the below requirement? [Requirement] ・Input voltage: 1Vpp Sin signal (DC2.5V) ・Output voltage: sin+ ：Same as input signal / sin- ：DC2.5V, AC…
    • Answered

  • OPA2170: ADA4692-2 Cross

    Resolved
    Part Number: OPA2170 Other Parts Discussed in Thread: OPA2834 , TLV9062 , TLV9052 , TLV9002 Hello, I am working to cross the ADA4692-2, and I think the best cross would be the OPA2170 or the OPA2834. Could you please confirm this? Additionally, what is our…
    • Resolved
    • Answered

  • RE: TLV9062: Output voltage swing

    Resolved
    Figure 10 does not go down to 0 mA. But extrapolating the lines implies that the device can reach the ±2.75 V rails. The datasheets of similar devices like the TLV9002/TLV9042/TLV9052 do show 0 mA, and have a voltage drop of 0 V at this point.
    • Answered

  • LM358A: Getting Wrong output Voltage

    Resolved
    Part Number: LM358A Other Parts Discussed in Thread: LM358 , TLV9002 , TLV6002 , LMV612 , TLV8542 , TLV9052 , LMV358 , LMV358A Hi, Please find the schematic, We are using LM358AD and giving 3.3V to Opamp IN+ pins, but we are getting 2.0V on output pins instead…
    • Resolved
    • Answered

  • RE: TLV9062: More Opamps usable as comparators?

    Resolved
    Hi David, We have quite a few of op amps that can be used as comparators. Most 5V devices can be used as comparators because they typically don't require the back to back diodes to clamp the differential input voltage. So, devices like the TLV9002, TLV9042…

Didn't find what you are looking for? Post a new question.