Search tips
Showing 89 results View by: Thread Post Sort by

  • TMDSECATCNCD379D: Integration Support TMDSECATCNCD379D

    Part Number: TMDSECATCNCD379D Hello, We are using PLC CX5140 and ET1100 which plugged on TI board TMDSECATCNCD379D. We used Reference Guide - SPRUIG9–September 2017 and User's Guide - SPRUIF9–August 2017. We want to communicate between…

  • TMDSECATCNCD379D: tmdsecatcncd379d

    Part Number: TMDSECATCNCD379D i want to generate pwm signals at pwm 2a and pwm 2b, based on the polarity of a sine wave. 2a should be off for positive half cycle, when 2b is on. The reverse happens during negative half cycle. Both are complementary signals…

  • TMDSECATCNCD379D: is this same as TMDSDOCK28379D + ethernet card

    TI Thinks Resolved
    Part Number: TMDSECATCNCD379D Other Parts Discussed in Thread: TMDSDOCK28379D , Hello, I do not want to use ethernet card. TMDSDOCK28379D is unavailable, hence planning to buy this. 1) WIll the same code developed for TMDSDOCK28379D work with this product…
    • Answered

  • TMDSECATCNCD379D: Failed CPU Reset: (Error -1138 @ 0x0)

    Resolved
    Part Number: TMDSECATCNCD379D Hello Dear TI Team, I am getting the error in the picture below when loading a program on my TI device. How can we solve this error? Also, the program that worked before on my device is not working now. Could this be because…
    • Resolved
    • Answered

  • TMDSECATCNCD379D: About Ethernet communication (With Beckhoff ET1100 ESC)

    Resolved
    Part Number: TMDSECATCNCD379D Other Parts Discussed in Thread: TMS320F28379D , TMDSCNCD28388D , Hello Dear TI Team, I am using the following development kit in the R&D project. I am doing EtherCAT communication (slave) with this development kit. www…
    • Resolved
    • Answered

  • TMDSECATCNCD379D: Program doesn't halt debugging on breakpoint

    Resolved
    Part Number: TMDSECATCNCD379D Hi, I place a breakpoint on line 354 of the code snippet in the image below. However, the program is not halting at this breakpoint line in debug mode. When I set a breakpoint on any line other than the 354-389 line range,…
    • Resolved
    • Answered

  • TMDSECATCNCD379D: CPU FLASH Program Running Error

    Resolved
    Part Number: TMDSECATCNCD379D Hello, I am successfully loading a program to DSP with flash configuration (CPU1_FLASH [Active]). And the program I loading to DSP works. I'm disconnecting the power of the DSP ControlCARD. Then, when I power the DSP again…
    • Resolved
    • Answered

  • RE: TMDSECATCNCD379D: SPI peripheral interface data transmit and receive error

    Resolved
    Hi, Veena: Veena Kamath said: We have one which interfaces the external EEPROM module AT25128. Where is this example in C2000Ware? Sinan, Thanks.
    • Answered

  • RE: TMDSECATCNCD379D: SPI CLK Frequency Calculate

    Resolved
    Hi, Gus : Thank you very much for your feedbacks. My problem is solved. I am thankful to you. Gus Martinez said: Could it be that you are not triggering your oscilloscope or logic analyzer correctly? The problem is caused by the incorrect my oscilloscope…
    • Answered

  • TMDSECATCNCD379D: CPU FLASH Program Loading Error

    Resolved
    Part Number: TMDSECATCNCD379D Other Parts Discussed in Thread: C2000WARE Hello, I am getting the error in the picture below when I loading a program on FLASH. I could not resolve the this error. What do you think could be the cause of this error? …
    • Resolved

Didn't find what you are looking for? Post a new question.