Answered

• TMS320F280037C-Q1: SPI INTERFACE FOR TMP125 WHEN USED WITH MULTIPLE SPI SLAVES GETTING 0XFFFF

  

  Prashanth Kumar M G

  Resolved

  Part Number: TMS320F280037C-Q1 Other Parts Discussed in Thread: TMP125 Hi Team, I am interfacing a TMP125 temperature sensor over SPI on a C2000 device. I am facing a strange issue where: The same SPI + TMP125 code works correctly in a standalone (bare…

  • Resolved

  • 4 months ago
  • C2000™︎ microcontrollers
  • C2000 microcontrollers forum
Answered

• TMP125: measure body temperature

  

  cafain

  Resolved

  Part Number: TMP125 HI, Staff TI's semiconductor sensors include temperature sensors, Is it possible to measure body temperature with these devices? Is it possible to use a TMP sensor to measure body temperature with a wearable device? please tell…

  • Resolved

  • over 4 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: without ESD information on datasheet

  

  Depeng Man

  Resolved

  Part Number: TMP125 Other Parts Discussed in Thread: TMP400 , Hi team ， Please provide their ESD information. Thank you. TI P/N TMP400SNAIDBQR TMP125AIDBVR ESD_HBM ESD_CDM

  • Resolved

  • over 4 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: non-volatile memory in the device

  

  Gerald

  Resolved

  Part Number: TMP125 Hi Team, May I ask for help? Our customer would like to know: is there any non-volatile memory in the TMP125 device, and if there is, can it be written to? I hope you can help us. Thank you so much. Kind regards, Gerald

  • Resolved

  • over 4 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: SO output pin state when CS bar is high?

  

  Denny Morgan

  Resolved

  Part Number: TMP125 What state does the SO output pin go to when CS bar is high? Low, high or tristate open? Or other?

  • Resolved

  • over 4 years ago
  • Sensors
  • Sensors forum

• TMP125: CS Data Read Operation

  

  Mark Ackerson

  TI Thinks Resolved

  Part Number: TMP125 Customer asked If we pull the CS pin low on the TMP125, then send 8 clock pulses to the serial clock, then pull the CS pin high, then some time later, pull the CS pin low again and clock out 16 clock pulses to the serial clock and…

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: IBIS or S-parameter model

  

  Connor Anderson

  Resolved

  Part Number: TMP125 Other Parts Discussed in Thread: TMP121 , Hello, I was looking for an electrical model to perform signal integrity analysis that would be compatible with Mentor's Hyperlynx such as an IBIS model or S-parameter model Thank you

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: Chip Select

  

  Mark Ackerson

  Resolved

  Part Number: TMP125 For the TMP125, if we hold SI (DIN) to GND to keep the part in continuous mode, is there any issue if CS is held low for more than 16 clocks? If CS was GNDed, does the part start new conversions? Or does CS need to be toggled? Regards…

  • Resolved

  • over 6 years ago
  • Sensors
  • Sensors forum
Answered

• TMP125: IBIS Model for SPI interface

  

  Michael T Schneider

  Resolved

  Part Number: TMP125 Other Parts Discussed in Thread: TMP121 Team, Do we have an IBIS model for the SPI interface for the TMP125. Or an equivalent IBIS model for the SPI interface for another device that we can use?

  • Resolved

  • over 5 years ago
  • Sensors
  • Sensors forum

• TMP125: SCK and Timing

  

  Mark Ackerson

  TI Thinks Resolved

  Part Number: TMP125 Please advise on questions regarding TMP125. The One shot and data read commands on pg 6 shows an initial SCK falling edge after CS drops low. Is this needed? We are planning to have SCK low initially when CS drops low. Not sure…

  • over 7 years ago
  • Sensors
  • Sensors forum

Didn't find what you are looking for? Post a new question.