Search tips
Showing 43 results View by: Thread Post Sort by
    Answered

  • TMP461-SP: Inquiry for electrical parameters not listed in datasheet of subject part number.

    Resolved
    Part Number: TMP461-SP Hello, I am working on a derating analysis per document number MDA-QS-003-PMAP-REVC (Appendix A), and wanted to know if you have more data available than what your datasheet has provided me. I am specifically inquiring the (1)…
    • Resolved

  • TMP461-SP: Need information on SET behavior under radiation

    TI Thinks Resolved
    Part Number: TMP461-SP Hi folks The existing SEE report for this device does not have any information on SET (single event transients). It only addresses SEL. https://www.ti.com/lit/pdf/sbok029 Is a more detailed test report covering SET available? If…

  • TMP461-SP: Cold Sparing Information

    TI Thinks Resolved
    Part Number: TMP461-SP Other Parts Discussed in Thread: TMP461 , Hello, Are there any cold sparing requirements on TMP461, particularly with the two-wire I2C serial interface? An FPGA is driving the SDA and SCL lines with the temp sensor as the slave device…
    • Answered

  • TMP461-SP: VOH specs for THERM outputs?

    Resolved
    Part Number: TMP461-SP Hello, I am looking at the DS for TMP461-SP and I did not see a VOH spec for THERM/THERM2. Are these known? Also, are there specs on the driver source current ? Thank you.
    • Resolved
    • Answered

  • TMP461-SP: SEU data

    Resolved
    Part Number: TMP461-SP Hi there. For this device it is mentioned there is a SEU report available on request. Please can I be provided a copy of this? I am using this device on a project. SEL and SET data is in the report available here on your site. …
    • Resolved

  • TMP461-SP: TMP461-SP SMBus Timing

    TI Thinks Resolved
    Part Number: TMP461-SP Other Parts Discussed in Thread: TMP461 From page 6 of the datasheet, the data setup (t(HDDAT)) and hold time (t(SUDAT)) is defined for writes on the SMBus. I need to know what the setup and hold time will be for the read cycle…

  • TMP461-SP: Termination of remote sense pins on the IC

    TI Thinks Resolved
    Part Number: TMP461-SP Hi, So the customer wants to u se TMP461-SP device for only local sensing purpose. He does not require it for remote sensing. So how does he terminate the D+ and D- pins? No guideline is given in the datasheet for the same. Thanks…
    • Answered

  • TMP461-SP: What resistor value can be used to connect A0 and A1 pins to VCC or GND

    Resolved
    Part Number: TMP461-SP Hi Experts! In space applications we typically frown on connecting signal pins directly to supply pins. For the Address (A0 and A1) pins of the TMP461-SP what is the maximum value resistor that can be used instead of a direct connection…
    • Resolved

  • TMP461-SP: Pin D- Internal Connection?

    TI Thinks Resolved
    Part Number: TMP461-SP We are having some testing issues with our TMP461-SP device. Debugging has lead me to need to know how the D- pin is connected in the device and if there is any ESD protection devices on it. What is D- connected to in the device…
    • Answered

  • TMP461-SP: TMP461-SP Sensor Fault

    Resolved
    Part Number: TMP461-SP Is there a typo in the TMP461-SP datasheet? "Short-circuit" should be "Open-circuit". 7.3.5 SensorFault The TMP461-SPdevice can sense a fault at the D+ input resulting from an incorrect diode connection. The…
    • Resolved

Didn't find what you are looking for? Post a new question.