Search tips
Showing 37 results View by: Thread Post Sort by
    Answered

  • TMS320F28035-EP: Memory error detection and correction

    Resolved
    Part Number: TMS320F28035-EP Tool/software: Hello, Are the internal memories of the TMS320F28035-EP protected by error detection and correction codes? Best regards, Zoran RACIC
    • Resolved

  • TMS320F28035-EP: ADC Reference Voltage

    TI Thinks Resolved
    Part Number: TMS320F28035-EP Tool/software: Hello, What would the default reference voltage for ADC? Is it external or internal reference mode. Please confirm!

  • TMS320F28035-EP: WDFLAG is not setting upon Watchdog reset during watchdog test

    Part Number: TMS320F28035-EP Other Parts Discussed in Thread: TMS320F28035 , C2000WARE Tool/software: Hello, I am trying to implement a watchdog test on the TMS320F28035. The goal is to enable the watchdog, provide a delay greater than the configured…

  • TMS320F28035-EP: Recovering from a break detect (BRKDT)

    TI Thinks Resolved
    Part Number: TMS320F28035-EP Tool/software: Our customer was performing systems integration and lost communication with our board. The customer captured a break detect event on the oscilloscope and showed it to us. Our board did not recover once the break…
    • Answered

  • RE: TMS320F28035-EP: TMS320F28035

    Resolved
    Ram, Prasanth Ram Jothikumar said: Please find the waveform attached herewith, these waveforms are taken while power stage is off. From evalautions, I wasnt able to see 3.3V in any of the pins ( TMS, TCK, TDI, TDO and TRST) -Image 1 . Is the F28035…

  • TMS320F28035-EP: Unable to select output file for flashing

    TI Thinks Resolved
    Part Number: TMS320F28035-EP Other Parts Discussed in Thread: C2000WARE Tool/software: Hello, I’m using CCS 12.8.0 with the TMS320F28035MPNTEP microcontroller and an XDS110 debugger. My .out file is located in the debug folder, but I don’t see an…

  • RE: TMS320F28035-EP: Configuring ADCINT1 as Internal Trigger for Continuous Conversion (No ISR Required)

    Hi, I apologize about the delay in getting back to you. MM said: AdcRegs.INTSEL1N2.bit.INT1E = 1; // Enable ADCINT1 Can you try setting this to zero? With the interrupt enabled, the CPU will branch to the stored location for the ISR. Since the…

  • TMS320F28035-EP: operating ambient temperature range

    TI Thinks Resolved
    Part Number: TMS320F28035-EP Tool/software: Hi We are looking for MCU with operating temperature range from -55deg C, through part filter reached this part #TMS320F28035-EP. However, datasheet section 4.4 mention ambient temperature range from -40…
    • Answered

  • TMS320F28035-EP: SPI communication between MCU and DAC is not working

    Resolved
    Part Number: TMS320F28035-EP Tool/software: Hi, I am using TMS320F28035MPNTEP microcontroller and DAC DAC80504RTET. Trying to communicate using SPIA. I tried to read Device ID of DAC from "Device ID register" and got garbage value. So started checking…
    • Resolved
    • Answered

  • TMS320F28035-EP: Clarification needed on CAN module clock

    Resolved
    Part Number: TMS320F28035-EP Tool/software: Hello, Please help me to understand CAN module clock. Is it always (SYSCLKOUT/2) or is it equal to LSPCLK? I am using Example_2803xECanBack2Back example, In comment its mentioned 30MHz CAN module clock.…
    • Resolved

Didn't find what you are looking for? Post a new question.