Filter by Reset

All
Forums (2,634)
  • C2000™︎ microcontrollers (2,352)
  • Code Composer Studio™︎ (201)
  • Processors (28)
  • Data converters (12)
  • Motor drivers (10)
  • Power management (6)
  • View all
Technical Articles (1)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 2,634 results View by: Thread Post Sort by
    Answered

  • TMS320F28377S: Create a contiguous binary for RAM execution in CCS

    Resolved
    Part Number: TMS320F28377S Other Parts Discussed in Thread: C2000WARE Tool/software: I have created a CCS 20.0.1.4 project for the TMS320F28377S. Now I have to adjust this project so that it is runnable in RAM. A colleague wants to load this program into…
    • Resolved
    • Answered

  • RE: TMS320F28377S: IEC60730SWPACKAGES: STL_HWBIST_runMicroTest()

    Resolved
    Will continue this conversation here: https://e2e.ti.com/support/microcontrollers/c2000-microcontrollers-group/c2000/f/c2000-microcontrollers-forum/1465198/tms320f28377s-cpu-register-address-inquiry

  • TMS320F28377S: TMS320F28377S Bypass Capacitors -- 0.01uF OK to use?

    TI Thinks Resolved
    Part Number: TMS320F28377S Tool/software: Hello, I am working on the bypass capacitor selection for the TMS320F28377S in a design and was wondering if 0.01uF capacitors would be sufficient instead of the 0.1uF as stated in the product datasheet for VDDIO…

  • RE: TMS320F28377S: Serial firmware update without using the boot mode pins.

    Hi Asad, Asad Hameed said: What if we set the boot mode pins for CAN boot mode so that the device always starts in the CAN boot mode. Is it then possible to jump to FLASH execution from the CAN boot mode in case the normal execution from FLASH is required…

  • TMS320F28377S: Blackhawk Debugger XDS560v2 Error: SC_ERR_PATH_BROKEN

    Part Number: TMS320F28377S Tool/software: Hi the Blackhawk debugger seems to be consistently failing with the below mentioned error. What could be the possible causes ? Is the debugger is failed beyond repair ? I am using CCS 8.0.0.2

  • RE: TMS320F28377S: spi and dma receive stuck

    Hello, I apologize again for the delay. I've looked into your settings, and your configurations look good. hello111 said: then RUN=1 outside the interrupt Where exactly in your code (under what conditions) are you re-enabling the DMA channel? It is…

  • TMS320F28377S: ADC Calibration TRIM Registers

    TI Thinks Resolved
    Part Number: TMS320F28377S Other Parts Discussed in Thread: C2000WARE Tool/software: ADC trim registers (ADCINLTRIM1 to ADCINLTRIM6) were described as ADC linearity trim bits 0 - 191 in TMS320F2837xs Microcontrollers Technical Reference Manual . In C20…

  • C2000-3P-SEARCH: Alignment Issue with TMS320F28377S Chip on TI Compiler Versions

    TI Thinks Resolved
    Part Number: C2000-3P-SEARCH Other Parts Discussed in Thread: C2000WARE Tool/software: Hi We have been developing our product using the TSM320F29377S chip. Our firmware builds successfully with Code Composer Studio (CCS) 9 using the TI v5.12.3.LTS compiler…
    • Answered

  • RE: TMS320F28377S: Power Sequencing Clarification

    Resolved
    Hello, It is an issue because VDDOSC and VDD should be powered on at the same time as explained in data sheet and Silicon errata.

  • TMS320F28377S: Tms320f28377s secure boot

    Part Number: TMS320F28377S Tool/software: Hello, We want to do secure boot with tms320f28377s, but it seems to exist in the datasheet of the processor, but there is no information about secure boot in the TRM, there is only information about the use of…
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.