Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 46 results View by: Thread Post Sort by
    Answered

  • RE: TMUX1209: Source or drain continuous current

    Resolved
    Hi K ameron , I'm sorry for the late reply. Thank you for your response. If I have any problems, I might contact you. Regards, Ryoma
    • Answered

  • TMUX1209: TMUX1209PWR POWER SOURCE

    Resolved
    Part Number: TMUX1209 Other Parts Discussed in Thread: INA827 , ADS1261 , , TMUX1109 Tool/software: Hi, I have designed a schematic for an analog measurement as shown below. On the analog input side, I can also receive negative analog signals from some…
    • Resolved
    • Answered

  • TMUX1209: TMUX1209

    Resolved
    Part Number: TMUX1209 HI iS THIS PART SUSCEPTIBLE TO LATCHUP? MUNIR
    • Resolved
    • Answered

  • TMUX1109: Drop-in replacement for TMUX1209

    Resolved
    Part Number: TMUX1109 Other Parts Discussed in Thread: TMUX1209 Hi, I have a PCB designed for TMUX1209PWR, but it is currently "out of stock" at pretty much any distributor I could find. According to the website TMUX1109 is a "drop-in replacement" for…
    • Resolved
    • Answered

  • TMUX1209: How do I calculate settling time

    Resolved
    Part Number: TMUX1209 Hi, I want to calculate 16-bit settling time of the MUX when channels are switched. The datasheet specifies settling time of 33ns for VDD =5V. The definition of settling time is given as "Transition time is defined as the time taken…
    • Resolved
    • Answered

  • TMUX1209: Internal equivalent circuit

    Resolved
    Part Number: TMUX1209 Hello expert, My customer is evaluating TMUX1209. Then, they observed100mV as high impedance on DA/DB during EN=0. I guess it is from internal protection diode or something but there isn't any explanation regarding this on datasheet…
    • Resolved
    • Answered

  • TMUX1209: Muxes keep breaking without warning

    Resolved
    Part Number: TMUX1209 Other Parts Discussed in Thread: TMP107 We have a 2 * 1:16 multiplexer device, which communicates with sensors and reads battery voltages. When measuring the batteries, we have an in-line resistor to protect from over current draw…
    • Resolved
    • Answered

  • TMUX1209: Can TMUX1209 be used as the multiplexer before ADS1118 to connect more thermocouplers?

    Resolved
    Part Number: TMUX1209 Other Parts Discussed in Thread: ADS1118 , , TMUX1109 Hello, We plan to use two chips of TMUX1209 together with ADS1118 to connect eight thermocouplers. Each channel of ADS1118 connect to one TMUX1209 which connect four thermocouplers…
    • Resolved
    • Answered

  • TMUX1209: high current draw with -2V / 0V referenced logic, analog at -2V / +3V

    Resolved
    Part Number: TMUX1209 Other Parts Discussed in Thread: TMUX1204 , Hi all My customer has preselected the TMUX1209 and the TMUX1204 because of the 1.8V logic compatible control inputs. In their system the uC supply is -2V / 0V while the analog supply for…
    • Resolved
    • Answered

  • TMUX1209: For UART to Slave

    Resolved
    Part Number: TMUX1209 Hey, when selecting a MUX for a UART. What parameters should I consider? In this case, What MUX can I use for a UART to connect to 3 slaves? Will a TMUX1209 work?
    • Resolved

Didn't find what you are looking for? Post a new question.