Search tips
Showing 26 results View by: Thread Post Sort by

  • TMUX6112: TMUX6112

    TI Thinks Resolved
    Part Number: TMUX6112 Hi, We are using analog switch part number TMUX6112PWR for differential input measurement. The Switch is used to complete a resistive path and the voltage drop across the resistor is to be measured ( Diagram 1). The Switch is biased…

  • TMUX6112: Do we have parts support better leakage current than TMUX6112?

    Part Number: TMUX6112 Hi experts, Do we have parts support better leakage current than TMUX6112? Marsh
    • Answered

  • TMUX6111: TMUX6111, TMUX6112, TMUX6113 Supply Voltage

    Resolved
    Part Number: TMUX6111 Hello TI, Just an FYI, the product selection table incorrectly lists +/-18V as an acceptable dual supply voltage for this family, when in fact, the maximum suggested supply is +/-17V No response needed, just figured you might want…
    • Resolved

  • RE: TMUX6112: Suitable PCB stackup

    Hi Faisal, Signals at those frequencies should not interact enough to cause any significant issues with routing them next to each other. Of course, it is advised to keep such traces at least 3x the trace width apart to minimize crosstalk, but usually…

  • TMUX6112: TMUX6112RTER

    TI Thinks Resolved
    Part Number: TMUX6112 Other Parts Discussed in Thread: TMUX6121 , TMUX6212 , OPA1622 Hello, For an audio application, I am looking for a quad Analog switch operating at +/- 5V fhat feeds into a summing inverting opamp where ON resistance of the switch isn…

  • TMUX6112: Undesired Spikes on I/O pin while switching

    TI Thinks Resolved
    Part Number: TMUX6112 Hello I am using TMUX6112 to build a switching circui.Here the rise and fall time of the select signal is 150ns and the IC is powered by Vdd = 10V (single). I can see the spikes on the Output pins as well as on the input pins with…
    • Answered

  • TMUX6112: Can it be used with Vdd= +7V and Vss = -4.5V?

    Resolved
    Part Number: TMUX6112 Hello, Can TMUX6112 be used with Vdd=+7V and Vss=-4.5V? Vdd to Vss ranges from 10V to 34V. Should Vss to GND range from -5V to -17V? Thank you, Shimon
    • Resolved

  • Spikes at TMUX6112 output

    TI Thinks Resolved
    Other Parts Discussed in Thread: DSLVDS1048 , TMUX6112 Hello I am using TMUX 6112 to implement an analog gate in combination with DSLVDS1048. But my output looks problematic. At the time of swiching, spikes are observed. The yellow waveform is the input…
    • Answered

  • TMUX6111: Are block diagram for TMUX6111 and TMUX6112 correct?

    Resolved
    Part Number: TMUX6111 Other Parts Discussed in Thread: TMUX6112 , TMUX1111 Dear Technical Support Team, Are block diagram for TMUX6111 and TMUX6112 correct on datasheet? TMUX6111 is normally closed and TMUX6112 is normally open. Best Regards, ttd
    • Resolved

  • TMUX6112: Ask for a SPICE Model

    TI Thinks Resolved
    Part Number: TMUX6112 Hi there, If you don't mind, can I ask a SPICE model for TMUX6112 (for LTSpice) ? I would really appreciate it. Thanks so much Sincerley SUNG

Didn't find what you are looking for? Post a new question.