Search tips
Showing 42 results View by: Thread Post Sort by
    Answered

  • TPA3100D2: Auto volume adjust solution

    Resolved
    Part Number: TPA3100D2 Hi, Does TI have total solution for monitor envirment sound and auto adjust volume solution? Thanks! Jeff
    • Resolved
    • Answered

  • TPA3100D2: TPA3100D2 35T AGP5

    Resolved
    Part Number: TPA3100D2 Hello The part no printed on the Ic is TPA3100D2 35T AGP5 What is the significance of the no’s 35T AGP5 Which follows the main part no in the ic TPA3100D2 35T AGP5 Thanks and regards Shreekumar
    • Resolved

  • RE: TPA3100D2: TPA3100D2 35T AGP

    Hi Shreekumar, TPA3128 is the next generation of TPA3100, with improved efficiency and audio performance. We actually don't have pin2pin compatible device with TPA3100. The orderable part number of TPA3100D2 doesn't include the "35T AGP5".…

  • TPA3100D2: TPA3100D2 Tcase temp over 110 deg

    TI Thinks Resolved
    Part Number: TPA3100D2 Other Parts Discussed in Thread: TPA3110D2 Dear, our client test thermal to do an experiment as below chart, use heat guns control 110°C, and we measurment Tcase =110°C also TPA3110D2 operating 20w and we find SPK +- output…
    • Answered

  • TPA3100D2: Figure 31 and Figure 32

    Resolved
    Part Number: TPA3100D2 Hi Team, The output voltage is different between Figure 31 and Figure 32. Is there any condition difference other than frequency (1kHz vs 8kHz)? I also doubt if the voltage range is correct or not. Best Regards, Yaita
    • Resolved
    • Answered

  • TPA3100D2: TPA3100 LC output filter, cut off frequency of 54khz

    Resolved
    Part Number: TPA3100D2 Dear, We saw the TPA3100D2 datasheet, about typical LC output filter, cutoff frequency of 28kHz...., speaker impendance=8 ohn L=33uH and C=1uF our client want LC output filiter, cutoff frequenct of 54kHz....., speaker impendance…
    • Resolved

  • RE: TPA3100D2: TPA3100D2 speaker output voltage

    Hi Satya, Usually the MSTR/SLV pin is set to High voltage to enable master mode. Best regards, Shawn Zheng
    • Answered

  • TPA3100D2: Supply goes dead on connecting speaker

    Resolved
    Part Number: TPA3100D2 I am trying to fix my bose soundtouch 30 speaker that uses the tpa3100d2 for powering the tweeters and a TDF8599BTHN1C for powering the woofer, both using a common power supply of 24 volts. This suddenly stopped giving any sound…
    • Resolved

  • TPA3100D2: related document for choosing the amp with related speaker

    TI Thinks Resolved
    Part Number: TPA3100D2 Other Parts Discussed in Thread: TPA3009D2 , TPA3136D2 Hi, i am using TPA3009D2 for my design. 1. i wanna know if there are documents discussing about how to choose proper amp? (mine is 5W at 4 ohm) , i want to know what is proper…

  • TPA3100D2: Can I use this device to drive 10 to 16 Ohm load from a 12-V supply?

    TI Thinks Resolved
    Part Number: TPA3100D2 Other Parts Discussed in Thread: TPA3136D2 Dear Sir, The TPA3100D2 spec informed that can operate on 10-W/ch into an 8-Ω Load from a 12-V supply. I’m wondering the TPA31002D2 at 12-V supply, is or not can to support these…

Didn't find what you are looking for? Post a new question.