Search tips
Showing 16 results View by: Thread Post Sort by

  • TPA4411: Short-Circuit and Thermal Protection

    TI Thinks Resolved
    Part Number: TPA4411 Hi team Could you explain in more detail about Short-Circuit and Thermal Protection? 1. When does the protection activate? Which current for SCP? Where temp? 2. How much is the threshold? Regards, Hayashi

  • TPA4411: Need TPA4411's Full Scale Input Voltage

    TI Thinks Resolved
    Part Number: TPA4411 Hi Sirs, Isn't TPA4411's input signal ground reference since we saw the input range is -0.3V to VDD+0.3V? Is there DC bias voltage at input pins? Can we say its full scale input range +/-0.3V? Thank you and Best regards, Wayne C…

  • TPA4411: Powerpads connected to GND

    TI Thinks Resolved
    Part Number: TPA4411 Hello On the data sheet it is stated that exposed PAD should be isolated from GND. However, I would like to ask you a few questions to change the design of the client. When you connect it to this, how is it structurally connected? …
    • Answered

  • Question of the TPA4411 ESD Rating

    Resolved
    Other Parts Discussed in Thread: TPA4411 , TPA6166A2 Hi Sirs, The TPA4411 datasheet specifies +/-8kV ESD rating on output ports only. Would you pls advise ESD rating o the other signal pins? Thanks a lot...Wayne Chen
    • Resolved
    • Answered

  • TPA4411 Voltage Tolerance of Output FETs

    Resolved
    Other Parts Discussed in Thread: TPA6132A2 , TPA4411 , TPA6133A2 , TPA6130A2 Hi, Could you please tell us the voltage tolerance for the output fets which are connected OUTR and OUTL ? Is our understanding correct although we believe that it is a double of…
    • Resolved

  • TPA4411 Output Impedance of OUTR and OUTL

    TI Thinks Resolved
    Other Parts Discussed in Thread: TPA4411 Hi, Could you please tell us the output impedance of OUTR and OUTL for TPA4411 as below? Best Regards, Kato
    • Answered

  • TPA4411 Workaround of Pop Noise

    Resolved
    Other Parts Discussed in Thread: TPA4411 , TPA6132A2 , TPA6133A2 Hi, Our customers have designed on page 3 of TPA4411 user's guide as below. However, when they return to normal mode from shut-down mode, the pop noise occurs. So, could you please tell us…
    • Resolved

  • TPA4411 Offset Voltage Causing Pop Noise

    TI Thinks Resolved
    Hi, When I return to the normal mode from the shut-down mode using pins of SDR and SDL, the pop noise occurs. I have obtained the reply that this cause is the offset voltage as below. http://e2e.ti.com/support/amplifiers/audio_amplifiers/f/6/p/338512/1182043…

  • TPA4411 Operation Principle that the Pop Noise Occurs

    TI Thinks Resolved
    Other Parts Discussed in Thread: TPA6132A2 , TPA6130A2 , TPA6133A2 , TPA4411 Hi, Could you please give me the operation principle that the pop noise occurs when I return to normal mode from shut-down mode using pins of SDR and SDL? Best Regards, Kato

  • TS5A22364DGSR and TPA4411 Device Characteristics

    Other Parts Discussed in Thread: TPA4411 Hello, One of my customers is looking at the following characteristics for TS5A22364DGSR: 1. Signal to Noise Ratio with reference to 0 dBm level measured at 1 kHz 2. % of Harmonic distortion of the line…

Didn't find what you are looking for? Post a new question.