• RE: TINA/Spice/TPD1S514: Spice model for TPD1S514

  

  Chuck Branch

  Joern, I am going to move this thread to TI thinks resolved because I haven't received the information necessary to evaluate generation of the Spice Model for this part. Regards, Chuck

  • over 7 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

• TPD1S514: OVP threshold

  

  Andy_Lin

  TI Thinks Resolved

  Part Number: TPD1S514 Hi Team, My customer is using this part(TPD1S514-1) as solution and their system operate in normal USB 5V application,they measured this part and found the OVP point is locked around 5.62~5.74V, which is a bit lower than out spec…

  • over 5 years ago
  • Interface
  • Interface forum

• RE: TPD1S514: replace NCP392A from OnSemi, which is EOL

  

  Ansel Song

  Hi As far as I know, there is not. And I don't think that NCP392A does not need caps as the below shown.

  • over 5 years ago
  • Interface
  • Interface forum

• TPD1S514: TPD1S514-1 : Over Voltage Protection

  

  Shmuel Davis

  TI Thinks Resolved

  Part Number: TPD1S514 Other Parts Discussed in Thread: TUSB320LAI , , TUSB320 , HD3SS3220 I ma using a TPD1S514-1 to protect my design when powering directly from the VBUS of a USB TYPE C port. Many of my components are rated at a Max of VCC = 5.5V (many…

  • over 8 years ago
  • Interface
  • Interface forum

• RE: TPD1S514: TPD1S514-1

  

  Chuck Branch

  Arne, What model do TI use for the 61000-4-5 100V spec: series resistance of 42 Ohm? Here is a link to the TI IEC 61000-4-x Tests: www.ti.com/.../slva711.pdf What is the clamping voltage of Vbus_con: appropriate 35v as in datasheet fig 8? The datasheet…

  • over 8 years ago
  • Interface
  • Interface forum

• TPD1S514: OVP device, need 7A constant current

  

  Shubiao Wang

  TI Thinks Resolved

  Part Number: TPD1S514 Other Parts Discussed in Thread: TPS25940 Hi , Do we have an OVP device, like TPD1s514-1, but with 7A constant current capacity? Best regards, Shubiao Wang

  • over 5 years ago
  • Interface
  • Interface forum

• TPD1S514: USB protection device with OVP,OCP and ESD function

  

  Nam, Dino

  TI Thinks Resolved

  Part Number: TPD1S514 Dear team, My customer consider using USB protection IC with OVP,OCP, ESD function. So I found TPD1S514 but this device has not OCP function. Is there proper device with OVP,OCP, ESD function? - application : USB charger /…

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• TPD1S514: A way to recognize VBUS short to GND for USB intetface

  

  Nam, Dino

  Resolved

  Part Number: TPD1S514 Dear team, Is there any way to recognize VBUS short to GND by water for USB interface? The customer want to know about interface device to protect VBUS short to GND by water. please let me know your opinion. Thank you.

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• TPD1S514: Current in VBUS_Power

  

  Lasse Korff

  Resolved

  Part Number: TPD1S514 Hi TI! I am not sure how to understand your datasheet of the TPD1S514x: On page 4 under Absolute Maximum Ratings it is stated that the maximum current from the LDO you provide in this component is 1 mA. However, on page 7…

  • Resolved

  • over 6 years ago
  • Interface
  • Interface forum
Answered

• TPD1S514: Spec for VBUS_POWER output over full input voltage range

  

  Ue

  Resolved

  Part Number: TPD1S514 Hi all My customer has this question: Looking at the spec of the TPD1S514-x USB protection switch, I could not find the complete spec of the VBUS_POWER output: I am looking for the maximum value on this output, for the full…

  • Resolved

  • over 6 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.