Search tips
Showing 17 results View by: Thread Post Sort by

  • TPS24742: Schematic review of TPS24742

    Part Number: TPS24742 Other Parts Discussed in Thread: CSD16415Q5 Hi team, My customer use the TPS24742 to realize r edundant power supplies. Below picture is the setting parameter from customer sides, Ilimt=9A. Customer used 'TPS2474x Design…
    • Answered

  • TPS24742: Should I connect exposed thermal pad to GND ?

    Resolved
    Part Number: TPS24742 Tool/software: HI there, Please let me know if I should connect exposed thermal pad of TPS24742 to GND. Thanks, Toru
    • Resolved

  • TPS24742: Priority Power MUX with No HS FET in Primary Power Path

    Part Number: TPS24742 Other Parts Discussed in Thread: TPS25983 Tool/software: Hi there, I 'm doing a design of Priority Power MUX with No HS FET in Primary Power Path using TPS24742. I do not need a HS FET in Primary Power Path of my Priority Power MUX…

  • TPS24742: Maximum Load Current in Transient Simulation for TPS24740EVM-596 Evaluation Module

    Part Number: TPS24742 Other Parts Discussed in Thread: TPS24740EVM-596 , PSPICE-FOR-TI , Tool/software: Hi there, I tried transient simulation for TPS24740EVM-596 Evaluation Module (actually half of it), but I could not get expected result for maximum…

  • TPS24742: TPS24742 Design and MOSFET

    TI Thinks Resolved
    Part Number: TPS24742 Other Parts Discussed in Thread: CSD16415Q5 , TPS24741 Hi, I am using the TPS24742 to build a over current protection and over voltage protection. My target voltage is 14V and current is 20A. I follow the instruction on the datasheet…
    • Answered

  • TPS24742: Is the current flowing through each channel equal when connected in parallel?

    Resolved
    Part Number: TPS24742 Hi experts, My cusotomer want to use TPS24742 to realize below structure. There is a question about below picture. If Vin1=Vin2=12V, and Iload=6A, is the current flowing through each channel equal? CH1=CH2=3A? Thanks! …
    • Resolved

  • TPS24742: For 3 battery backup power

    Part Number: TPS24742 Hi, My customer have a 3 battery backup power system want used TPS2474x. If they have own MCU can monitor battery voltage level, want used GPIO to control the TPS2474x, how to control the ENOR and ENHS? Ideal behavior as below…
    • Answered

  • TPS24742: TPS24742 - does not work

    Resolved
    Part Number: TPS24742 Other Parts Discussed in Thread: TPS25942A Hello. I developed the scheme Hotswap then ORing (TPS24742). When the power supply is 12 volts, the power supply delivers a current of 5 amps and starts to warm the Hotswap mosfet. At the…
    • Resolved
    • Answered

  • TPS24742: Design Calculator error - Rev B

    Resolved
    Part Number: TPS24742 This applies to the TPS2474x Design-in Calculation Tool Rev B available on the ti.com as of today. In the Reverse Current Threshold section... (Step 7) When calculating the min rdson in cell F115, the formula is "F113/F114" This…
    • Resolved
    • Answered

  • RE: TPS24742: Power management forum

    Resolved
    For TPS24742 also there is no delay after Over voltage recovery. You can have a look at section 10.3.2 in datasheet. The Auxiliary rail OV pin is connected to VMAIN such that when VMAIN drops below 11V, VAUX recovers from Overvollatge and starts delivering…

Didn't find what you are looking for? Post a new question.