Search tips
Showing 27 results View by: Thread Post Sort by

  • TPS2482: Assistance in Selecting a Hot Swap Controller – Issue with TPS2482 Soft-Start

    TI Thinks Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: TPS2483 , TPS2493 Tool/software: Hi TI Support Team, We are designing a hot swap controller for a 24V nominal battery-powered mobile robot with the following key requirements: Peak Load: 600W…
    • Answered

  • TPS2482: Using the TPS2482 as E-Fuse - Current Limiter

    Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: TPS1663 Tool/software: Hello, We're using the TPS2482 as E-Fuse current limiter for the resistive load of 5 ohm. VIN = 28V R_SESNSE = 9mOhm Current Limit = 5A Timer cap = 330nF R3 …
    • Resolved
    • Answered

  • TPS2482: Insufficient gate drive voltage.

    Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: MSP430F247 , , TPS2480 Tool/software: My circuit works (briefly on initial power up) but fails to sustain the gate voltage on the output transistor Q500. I am controlling the Enable pin directly from…
    • Resolved

  • TPS2482: Insufficient gate drive voltage.

    Part Number: TPS2482 Other Parts Discussed in Thread: MSP430F247 , , TPS2480 Tool/software: My circuit works (briefly on initial power up) but fails to sustain the gate voltage on the output transistor Q500. I am controlling the Enable pin directly from…

  • TPS2482: Insufficient gate drive voltage.

    Part Number: TPS2482 Other Parts Discussed in Thread: MSP430F247 , , TPS2480 Tool/software: My circuit works (briefly on initial power up) but fails to sustain the gate voltage on the output transistor Q500. I am controlling the Enable pin directly from…

  • TPS2482: No suitable slew-rate even though other TI hotswap calculators can make it work

    TI Thinks Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: LM5069 Tool/software: Hi I want to use TPS2482 to precharge 9mF with a steady state current limit of 6A at 24V. Because I want fast over-current response time, I need external soft start control…
    • Answered

  • TPS2482: Softstart

    Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: TPS2663 Tool/software: Hi, We're using the TPS2482 to turn power on and off from a 24V battery. We need to switch 13.2mF of capacitance for motor drive bulk capacitance. I've been working with the…
    • Resolved
    • Answered

  • TPS2482:

    Resolved
    Part Number: TPS2482 The TPS2482PWR in my circuit isn't functioning as typically expected when enabling the chip after the load and the supply power Vin are applied. The steps I made during operational testing of the TPS2482PWR are listed below: 1.…
    • Resolved

  • TPS2482: i want pspice model library for simulation purpose

    TI Thinks Resolved
    Part Number: TPS2482 Other Parts Discussed in Thread: TPS2492 TPS2482 - i want pspice model library for simulation purpose. can you send me the this library file.

  • TPS2482: relationship where lower current limit needs lower slew rate

    Part Number: TPS2482 Hello, I have a question regarding the use of the TPS2482. We are using the TPS2482 as an inrush controller and utilizing output voltage slew rate control by placing a resistor and capacitor on the gate of the input mosfet. During…

Didn't find what you are looking for? Post a new question.