Answered

• TPS53318: Technology process for TPS53318

  

  Dan Barr

  Resolved

  Part Number: TPS53318 What was the smallest technical process node (Jejomar's response showed "multiple") used to manufacure the TPS53318. Jejomar Ildefonso of the Texas Instruments | Customer Support Center suggested I direct this question to this E2E…

  • Resolved

  • 5 months ago
  • Site support
  • Site support forum

• TPS53318: Technology process

  

  Dan Barr

  TI Thinks Resolved

  Part Number: TPS53318 What was the technical process node use to manufacure the TPS53318. Jejomar Ildefonso of the Texas Instruments | Customer Support Center suggested I direct this question to this E2E forum support form. Specifically, what was the…

  • 5 months ago
  • Site support
  • Site support forum

• TPS53318: TPS53318 - no output voltage if there is a load on the output

  

  Michi S

  TI Thinks Resolved

  Part Number: TPS53318 Tool/software: We designed in the TPS53318 on a new board like WEBENCH created the schematic for an input voltage of 12 V and an output voltage with 3,3 V @ 4 A. If the output is open (no load) there are 3,3 V at the output…

  • over 1 year ago
  • Power management
  • Power management forum

• TPS53318: Issue facing with TPS53318

  

  Anmol Jaiswal

  Part Number: TPS53318 Hi I have designed a PCB for converting 16V to 5V using TPS53318 but i am not able to get the desired output. i am getting 0.2-0.3V on the output and feedback as well. I am adding the schematic here for your reference as i…

  • over 3 years ago
  • Power management
  • Power management forum

• TPS53318: The output voltage is normal when there is no load. After loading, the output pulses occur.

  

  Songchangzhi song

  Part Number: TPS53318 Tool/software: I designed the circuit using the TPS53318 chip. Could you please point out where the design is not reasonable? When the load is applied, the output becomes a pulse waveform.Please help me analyze this.

  • over 1 year ago
  • Power management
  • Power management forum

• TPS53318: TPS53318DQPR Schematics Verification

  

  Nachiketh Karanth

  TI Thinks Resolved

  Part Number: TPS53318 Tool/software: Hi, Please verify the schematics for Vin = 12V and Vout = 1.8V. Thanks /cfs-file/__key/communityserver-discussions-components-files/196/TPS53318DQPR.pdf

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• TPS53318: TPS53318 TPS53355

  

  Robert Liu

  Resolved

  Part Number: TPS53318 Other Parts Discussed in Thread: TPS53355 Hello! With the same input voltage, output voltage and output current, it is not necessary to change the schematic diagram and PCB. Can tps53355 replace tps53318? thank you!

  • Resolved

  • over 4 years ago
  • Power management
  • Power management forum

• TPS53318: TPS53318 VS TPS53319

  

  Jimmy Lai

  TI Thinks Resolved

  Part Number: TPS53318 Other Parts Discussed in Thread: TPS53319 , Dear Team, I would like to ask you about TPS53318 and TPS53319. 1. Are they fully pin to pin? In addition to the current capacity, one is 8A and the other is 14A, what are the main…

  • over 4 years ago
  • Power management
  • Power management forum

• TPS53318: TPS53318 design review

  

  Peter Tseng

  TI Thinks Resolved

  Part Number: TPS53318 Dear Sirs, Please help to review if there is any problem with customer design. Thanks. sche.pdf

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• TPS53318: TPS53318DQPT About the output voltage when overcurrent is detected

  

  Koji Matsuo

  Resolved

  Part Number: TPS53318 Other Parts Discussed in Thread: TPS53319EVM-136 , TPS53319 , TPS53318DQPT About the output voltage when overcurrent is detected Modify TPS53319EVM-136 according to the attached schematic diagram. conditions ・VIN(VREG_1P8V) 1…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.