Search tips
Showing 210 results View by: Thread Post Sort by

  • TPS61023: Product recommendation

    Part Number: TPS61023 Other Parts Discussed in Thread: TPS61299 Hi expert, my customer want to use TPS61023 to work in this condition(Iomax=2A). Is TPS61023 suitable in this case or do we have a better solution? thanks! (1)4＜Vin≤5V, Vo=5.2V (2)5V＜Vin…

  • TPS61023: SEM problem with low voltage of 2.2V

    Part Number: TPS61023 When the low-voltage 2.1V power supply is used, we test the SEM performance of B256 and find that there is an obvious spur at 1M. After investigation, it is found that the Boost switching frequency is transmitted to our PA…

  • TPS61023: Easily burned during work

    Part Number: TPS61023 hi sir vin 4v boost to 5.2V, it's Easily burned during work could you help to check the schmatic? thanks

  • TPS61023: TPS61023DRL Design Review Needed

    Part Number: TPS61023 Other Parts Discussed in Thread: TPS61022 Hi, Need design review of the below design: VSYS can vary between 3.3V to 4.2V. Maximum output current can be 5V. Need the output supply clean and with low noise. Also, trying…
    • Answered

  • TPS61023: it it recommended to connect 4.2V 60Ah battery pack to this as input?

    Resolved
    Part Number: TPS61023 Other Parts Discussed in Thread: TPS63700 Hi team, We have a requirement to connect a 4.2V 60Ah battery pack as input to the TPS61023. We need to ensure compatibility with this input specification. We are currently finalizing this…
    • Resolved
    • Answered

  • TPS61023: INPUT VOLTAGE 1V IOUT=?

    Resolved
    Part Number: TPS61023 Other Parts Discussed in Thread: TPS61022 , TPS61022EVM-034 Hi. Looking at the datasheet 1PAGE, VIN=0.5V ~ 5.5V. 6PAGE FIGURE 6-3, which indicates that the output power current can be 1A or higher when VIN = 1.8V - 4.2V. …
    • Resolved

  • TPS61023: Bad regulation with load when the power is being supplied through long wires.

    Part Number: TPS61023 Hi TI Team. I am designing a board where I use the TPS61023 boost converter. Input = 3-4.2 V. Output = 5V at 1A. The connections are the following: As you can see, 5V DC-DC Converter (TPS61023) can be powered from the internal…
    • Answered

  • TPS61023: Output voltage increases with closeness of finger....

    Resolved
    Part Number: TPS61023 So I built this circuit using webench. I've attached the SCH & PCB. It's a simply 2 layer PCB, not much going on. The circuit outputs 2.15V as advertised. Currently I have a 200mA load connected, everything is hunkey dorey. When…
    • Resolved
    • Answered

  • TPS61023：PMP15037 reference design

    Resolved
    Part Number: TPS61023 Other Parts Discussed in Thread: TPS61021A , PSPICE-FOR-TI Hello Texas Instruments Community, good day, I want to design two groups of LED drivers with reference to PMP15037, but TPS61021A can only provide 1A driving current…
    • Resolved
    • Answered

  • TPS61023: Power management forum

    Resolved
    Part Number: TPS61023 Other Parts Discussed in Thread: TPS61021A , PSPICE-FOR-TI Hello Texas Instruments Community, good day, I want to design two groups of LED drivers with reference to PMP15037, but TPS61021A can only provide 1A driving current…
    • Resolved

Didn't find what you are looking for? Post a new question.