Search tips
Showing 52 results View by: Thread Post Sort by
    Answered

  • TPS62866: TPS628660AYCGR and TPS628660DYCGR Difference

    Resolved
    Part Number: TPS62866 Hi Team, Could you pls advise the spec difference between TPS628660 A YCGR and TPS628660 D YCGR? Thank you. Best regards, Mike
    • Resolved
    • Answered

  • TPS62866: TPS62866 A/B version for same design

    Resolved
    Part Number: TPS62866 My customer want to design TPS62866 A & B version in same schematic. Can customer pull A2 pin low to GND with R=105kohm to compatible A & B version ? According to D/S, pull low = "Vout register 1" for A version. but not same…
    • Resolved
    • Answered

  • TPS62866: Question for TPS62866 recommended junction temperature when lifetime is reduced for long time operation

    Resolved
    Part Number: TPS62866 Hi Team, From TPS62866's datasheet, we claimed that for recommended operating conditions, the recommended junction temperature should be no more than 85C for 6A operating continuously, but our customer also wants to know what's…
    • Resolved
    • Answered

  • TPS62866: I2C address corresponding to an invalid Vset resistor

    Resolved
    Part Number: TPS62866 Hi, I am using the part switching regulator TPS62866. The Vset resistor values and the corresponding I2C addresses are specified in the table for setting the output voltage. If a resistor value outside those mentioned in the…
    • Resolved

  • TPS62866: Higher Vin device of TPS62866

    TI Thinks Resolved
    Part Number: TPS62866 Hello, The customer look for Vin (max) = 6V, Iout = 6A, the step of voltage change is 5mV through I2C device. TPS62866 is near part but VIN can't meet VIN >= 6V spec. Is there any alternative device to meet VIN spec? Best regards…
    • Answered

  • TPS62866: VIN related questions

    Resolved
    Part Number: TPS62866 Hello, My customer has some questions about TPS62866. Q1: Looking at Figure 8-1 of the datasheet, VIN rises first then EN ramps. But, VIN and EN can be connected and they can ramp simultaneously? Q2: They would like to confirm…
    • Resolved
    • Answered

  • TPS62866: Without MCU use

    Resolved
    Part Number: TPS62866 Other Parts Discussed in Thread: TPS62867 Hi team, My customer that wants to design in TPS628660BYCGR and he have a quick question. If there is no MCU at their system, do they just need to set VSET resistor for setting the output…
    • Resolved
    • Answered

  • TPS62866: SDA/SCL pin status during EN=Low

    Resolved
    Part Number: TPS62866 Hello, My customer is sharing TPS62866 I2C interface with other I2C slave devices. When VIN is on and EN is low, TPS62866 SDA and SLC pins are floating so that they do not disturb I2C communication between host and other slave I2C…
    • Resolved
    • Answered

  • TPS62866: Comparable DCS-Control Regulator w/ EVM Supporting Loop Stability Testing

    Resolved
    Part Number: TPS62866 I am working on a design incorporating the TPS62866, however the design is too dense to allow for a resistor in series with the VOS pin. In this situation, I'd do my testing & tuning on the EVM, however the TPS62866EVM-051 does…
    • Resolved
    • Answered

  • TPS62866: How to test bode plot

    Resolved
    Part Number: TPS62866 Hi team, There are not resistor divider on TPS62866 schematic. Could we do Bode plot test on TPS628660D? Or it doesn't need test bode plot like the DCAP device? Best regards, Hardy
    • Resolved

Didn't find what you are looking for? Post a new question.