Search tips
Showing 46 results View by: Thread Post Sort by
    Answered

  • TPS7A4701-EP: TPS7A4701

    Resolved
    Part Number: TPS7A4701-EP Other Parts Discussed in Thread: TPS7A33 , TPS7A94 Hello, My question is about positive regulated ultra-low noise LDO TPS7A4701 and negative regulated ultra-low noise LDO TPS7A33. For TPS7A4701's output current of 85uA, and for…
    • Resolved

  • TPS7A4701-EP: TPS7A4701,TPS7A33

    TI Thinks Resolved
    Part Number: TPS7A4701-EP Other Parts Discussed in Thread: TPS7A33 , LMZ31704 , LM27762 , TPS7A39 , TPS65131 , TPS7A91 , TPS7A47 , TPS7A52 , LM27761 I am designing a power supply circuitry for the analog front end of my isolated data acquisition module. The…
    • Answered

  • TPS7A4701-EP: clarification on Y axis of figure 2 and 3 in the datasheet

    Resolved
    Part Number: TPS7A4701-EP Team, Would you be able to elaborate on the Y axis label in figures 2 and 3 of the datasheet? Can you walk through how to read the graphs? wondering how to interpret +/-100+% of the values. appreciate your help!
    • Resolved

  • TPS7A4701-EP: technology discussion

    TI Thinks Resolved
    Part Number: TPS7A4701-EP Dear. Currently customer is using TPS7A4701RGWT， in datasheet ，it shows thermal pad is internally connected to GND as below, but in actual，we find there is no connected between thermal pad and pin 7 GND ，Could you help me confirm…

  • TPS7A4701-EP: TPS7A4701RGWR

    TI Thinks Resolved
    Part Number: TPS7A4701-EP LDO POWER IC WITH 24.5V INPUT AND OUTPUT IS 24V @1A.
    • Answered

  • TPS7A4701-EP: prop delay & timing of EN pin to output for shutdown

    Resolved
    Part Number: TPS7A4701-EP Team - quick question: Assuming that the linear regulator is up and running steady state and then the the enable pin of the part gets pulled down with a fast edge (using a small signal mosfet, a digital gate, etc). How long does…
    • Resolved
    • Answered

  • TPS7A4701-EP: NC pins connection

    Resolved
    Part Number: TPS7A4701-EP Dear all, We are using TPS7A4701-EP convert from 15V to 5V. We notice that NC pins are connected to GND in the EVB whereas it’s open in our design. In datasheet, it shows that it’s acceptable either left to open or connect…
    • Resolved
    • Answered

  • TPS7A4701-EP: Input Impedance

    Resolved
    Part Number: TPS7A4701-EP Other Parts Discussed in Thread: TPS74401-EP Team, I have a question on the TPS7A4701-EP and TPS74401-EP LDOs. I’d like to know what it would the simulation model for the Input Impedance of the LDO seeing from its Input Power…
    • Resolved

  • TPS7A4701-EP: Paralleling TPS7A4700RGWR

    TI Thinks Resolved
    Part Number: TPS7A4701-EP Other Parts Discussed in Thread: TPS7A47 Is it possible to paralleling two or more TPS7A4700RGWRs to increase the ouput current?

  • TPS7A4701-EP: Sink current

    TI Thinks Resolved
    Part Number: TPS7A4701-EP HI TI, I am using TPS7A4701RGWR for RF application, where I generate 28V from 28.5V. This RF circuit has few Pin diode Switches. Since I have PIN DIODE this LDO might have to sink -100mA current, So what is the sink current capability…

Didn't find what you are looking for? Post a new question.