• 

  Shinji Tsuji

  • 3 months ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: Soft Start specification

  Part Number: TPS7A6650H-Q1 Hi team, Could you advise the soft start specification of TPS7A6650-Q1 such like duration time, limited current value, any threshold? Soft start function is described in the datasheet, but no parametric spec is defined in...
• 

  Stephen Ziel

  • 7 months ago
  • Power management
  • Power management forum

  RE: TPS7A6650H-Q1: work status is not normal

  Hello, I believe you are using 3 parallel output capacitors, with manufacturing part number (CGA4J3X8R1C105K125AE) in parallel on the output. When you say "3 ways circuit", are you describing 3, TPS7A6650's in parallel? This can be completed...
• 

  Jason Song

  • 9 months ago
  • Power management
  • Power management forum

  RE: TPS7A6650H-Q1: Vbat short

  Hi Jon, This device does not have a built-in short-to-battery protection. A battery voltage in a 12V car system is normally considered to be 14V typically. If the input of the LDO has a voltage less than 14V, the LDO needs to have external diode from...
• 

  Dexter Choi60

  • over 1 year ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: request Enable delay time for TPS7A6650QDGNRQ1

  Part Number: TPS7A6650H-Q1 Dear Sir, Could you please provide enable delay time as below pictures. I need to know Enable time of two case as Low to High and High to Low condition. Enable Low to high Enable High to Low
• 

  D

  • over 1 year ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: TPS7A6650 Power Good

  TI Thinks Resolved

  Part Number: TPS7A6650H-Q1 For the TPS7A6650-Q1, if the EN pin is low, does the PG pin still function? In other words, will PG be active low, or does PG only function when EN is high? According to the block diagram, it looks like PG needs the EN to be...
• 

  Relay Man 2

  • over 1 year ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: Power Good (PG) pin pull up to 3.3V

  • Resolved

  Part Number: TPS7A6650H - Q1 Hi, We have an application where the power supervision is done
• 

  keith leisses

  • over 1 year ago
  • Power management
  • Power management forum

  RE: TPS7A6650H-Q1: Power Pad connected to?

  thank you for the explanation.
• 

  Gerald Choi

  • over 2 years ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: What is the frequency of the output area?

  Part Number: TPS7A6650H-Q1 Dear Linear Regulators team What is the frequency of the output area on TPS7A6650H-Q1? Best Regards Gerald.
• 

  Gerald Choi

  • over 2 years ago
  • Power management
  • Power management forum

  TPS7A6650H-Q1: TPS7A6650H-Q1 Enable Threshold

  TI Thinks Resolved

  Part Number: TPS7A6650H-Q1 Dear Linear Regulators team We have a schematics for TPS7A6650H-Q1 as a below. And then, We want ENABLE pin to Low status that if 1.7V under should be make Enable pin Low immediately? Of course We know Voltage...
• 

  Herman Theodorus

  • over 1 year ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: TINA/Spice/TPS7A6650H-Q1: TPS7A6650H-Q1/TPS7A6633: TINA-TI model request

  Hi Andres, For this part, you can request the unencrypted model through TI Support: www.ti.com/.../calltisupport.tsp . Then you can import the model to TINA-TI. Make sure to scroll down toward the bottom of the page. If TI Customer Support that...

Didn't find what you are looking for? Post a new question.

• Ask a new question