Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 65 results View by: Thread Post Sort by

  • TPS7H2201-SP: TPS7H2201-SP

    TI Thinks Resolved
    Part Number: TPS7H2201-SP Hello, I'm looking for a load switch to provide soft-start and reverse-polarity protection, the output from the isolated DC-DC is +5V and the current is ~2A. Ideally I'd like to use a commercial-grade device for an initial prototype…
    • Answered

  • TPS7H2201-SP: What is the reaction time in case of a SEL?

    Resolved
    Part Number: TPS7H2201-SP Hi I plan to use the TPS7H2201-SP to protect a SEL sensitive load and would like to know the reaction time of the component. By reaction time I mean how long the SEL must be for the chip to start limiting. Thanks in advance for…
    • Resolved
    • Answered

  • TPS7H2201-SP: Question about redundancy application of TPS7H2201-SP.

    Resolved
    Part Number: TPS7H2201-SP Hi expert, My customer want to use hot sparing application (Two powersupplies ON at the same time) by TPS7H2201-SP . Is it possible? Or any advise? Thanks!
    • Resolved
    • Answered

  • TPS7H2201-SP: Question about reverse current protection of TPS7H2201-SP.

    Resolved
    Part Number: TPS7H2201-SP Hi expert, For below schematic. If my 5V secondary source short to GND and EN secondary keep high, looks like it will generate a reverse current go through the TPS7H2201-SP. In this situation, will TPS7H2201-SP reverse current…
    • Resolved

  • TPS7H2201-SP: tps7h2201-sp: Internal Pull-down Resistor

    TI Thinks Resolved
    Part Number: TPS7H2201-SP Hello. I have a couple questions about a datasheet for a load switch. The part number is tps7h2201-sp In figures 4 and 5, max pull down spec is at 138 ohms and graph doesn't go anywhere near that for load switch Rpd. How was…
    • Answered

  • TPS7H2201-SP: TPS7H2201-SP: thermal resistance

    Resolved
    Part Number: TPS7H2201-SP Hello, are the thermal resistance values (Theta JB and Theta JC) available for this part? Thank you, Evan
    • Resolved
    • Answered

  • TPS7H2201-SP: TPS7H2201-SP won't disable output

    Resolved
    Part Number: TPS7H2201-SP Hello, I am using the TPS7H2201-SP component and I am unable to switch off the load. I have a 5V input, when I turn the enable low my output only reduces to 1.3V This is my implementation. The enable signal has no noise. I…
    • Resolved
    • Answered

  • TPS7H2201-SP: About the difference of EVM and /EM part.

    Resolved
    Part Number: TPS7H2201-SP Hi expert, My customer have some doubts about the difference beteween /EM part and EVM. They bought the EVM for evaluation of component performance and intend to do the electrical test with /EM part, but they also notice /EM part…
    • Resolved

  • TPS7H2201-SP: About the test of metal whisker for space products.

    Part Number: TPS7H2201-SP Hi expert, My csutomer ask to provide below items "per lot" shipping to them. a. Failure Rate or MTBF b. TID report c. SEE report d. PIND report e. Metal whisker report 1. As I know, the MTBF can be found in "Quality…

  • RE: TPS7H2201-SP: TPS7H2201-SP

    Hi Elif, I was able to recreate results similar to what you observed. The device does reach fairly high temperatures when switching on and off due to over-current limit protection features. This took around 1-2 minutes on the default TPS7H2201-SP EVM…

Didn't find what you are looking for? Post a new question.