TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 32 results View by: Thread Post Sort by
  • TPS84620: Switching frequency set to 500 KHz

    PRAHLAD Supeda
    PRAHLAD Supeda
    TI Thinks Resolved
    Part Number: TPS84620 Other Parts Discussed in Thread: LMZM33606 Need 12Vin to 5Vout @ 6A power module design with 500 KHz switching frequency. 500 KHz is a mandatory requirement. Couldn't find option to set TPS84620 to 500 KHz for above Vin & Vout…
    • over 6 years ago
    • Power management
    • Power management forum
  • RE: TPS84620: Power up Sequence waveform is not smooth

    J Arrigo
    J Arrigo
    From the waveforms, the input voltage is dropping when both output voltages are turning on. The current capability of your input supply may need to be increased. You may try delaying the turn on of the output voltage until VIN is higher by using the UVLO…
    • over 7 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS84620 Resistor and Cap Settings

    John Kasson
    John Kasson
    Resolved
    Other Parts Discussed in Thread: TPS84620 Hello, In my design I'm using a TPS84620 to produce 2.5V and I want to make sure I get the resistor and cap settings correct. On Table 1 it shows for 2.5V that Rrt should be set 1K ohm while Table 2. says…
    • Resolved
    • over 10 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS84620 RT/CLK resistance calculation formula

    Bob Lee62837
    Bob Lee62837
    Resolved
    Other Parts Discussed in Thread: TPS84620 Dear support team, I decide the switching frequency of the TPS84620. Could you teach the calculation formula for determining the resistance value of the RT / CLK? Regard. Bob Lee
    • Resolved
    • over 11 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS84621 and TPS84620 Voltage feedback loop - Reference voltage (Vref)

    kavitha narayandass
    kavitha narayandass
    Resolved
    Other Parts Discussed in Thread: TPS84621 , TPS84620 Hi All, Can any one tell me reference voltage used in the feedback loop and its tolerance value for TPS84621 and TPS84620? Thanks in advance.
    • Resolved
    • over 11 years ago
    • Power management
    • Power management forum
  • Answered
  • Re: TPS84620 Package dimensions

    Colleen Kilroy
    Colleen Kilroy
    Resolved
    Hi Jimmy, Please note that the TPS84621 has a wider output voltage range, down to 0.6V. This is fully released and is completely pin-to-pin compatible with the TPS84620, and the same height dimensions. http://www.ti.com/product/tps84621 Regards…
    • over 13 years ago
    • Power management
    • Power management forum
  • Answered
  • TPS84620/1 current sharing

    1351769
    1351769
    Resolved
    Other Parts Discussed in Thread: TPS84621 , TPS84620 Hello, Can the TPS84620 or the TPS84621 operate in current sharing mode like the LMZ2xxxx series? Thanks
    • Resolved
    • over 12 years ago
    • Power management
    • Power management forum
  • Answered
  • Re: TPS84620 used as LED driver

    J Arrigo
    J Arrigo
    Resolved
    Hi Norbert, It may be possible to configure this device as a constant current source similar to how you describe above. I would need to know more details of your application. I would also want to add in some protection for both the LED and the TPS84xxx…
    • over 13 years ago
    • Power management
    • Power management forum
  • Answered
  • Re: Derating Temperature Curve for TPS84620

    JohnTucker
    JohnTucker
    Resolved
    There is not really a derating curve per se. The thermal performance is almost completely determined by the PCB design and other external operating conditions. The limiting factor is maximum junction temperature. The thermal parameters are in teh data…
    • over 14 years ago
    • Power management
    • Power management forum
  • LMZ31506: About slow start of LMZ31506

    hisashi yoda
    hisashi yoda
    TI Thinks Resolved
    Part Number: LMZ31506 Other Parts Discussed in Thread: TPS84621 , TPS84620 , TPS82130 LMZ31506のスロースタートについて教えてください。 LMZ31506のデータシートの9.16 Slow Start (SS/TR)にて、時間とコンデンサの定数の関係についてTable6に記載されていますが、計算方法はどこに記載されていますか? データシートは下記リンクを参照しております。 www.ti.com/.…
    • over 3 years ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question