Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 17 results View by: Thread Post Sort by

  • TS12A44514: Test setup to measure Input leakage current

    TI Thinks Resolved
    Part Number: TS12A44514 Hi Team, My customer wants to know the experimental setup to measure "Input leakage current" correctly. Could you tell me the setup which you used in device characterizing process? We especially want to know how we should…

  • TS12A44514: TS12A44514 - the consumption current of Vcc

    TI Thinks Resolved
    Part Number: TS12A44514 I want to drive the input controls using a DIO. How much current draw will each input require for a High and a Low?

  • RE: TS12A44514: TS12A44514

    Pratik, The TS12A44514 is a passive FET switch and would not support 2000 V on the signal path for any significant duration other than an ESD type event. When the TS12A44514 is toggled to the off state the signal path will be Hi-Z in the ~1M ohm range…

  • TS12A44514: V,IH at VCC = 12V

    TI Thinks Resolved
    Part Number: TS12A44514 Other Parts Discussed in Thread: MUX509 Team- For VCC = 12V, page 6 of data sheet indicates that VIH,min = 5V. However, section 8.1.1, page 11, states that "...When Vcc reaches 12V, the level threshold is about 3V". …

  • TS12A44514 as Resistor Switch

    TI Thinks Resolved
    Other Parts Discussed in Thread: TS12A44514 , TS5A22362 , TS12A4516 Hello, I'm using the TS12A44514 as a resistor switch as a part of PGA, using the following schematics: R11 is the RF, set to 510 ohm, and RG = R15 || R switch. It is a non-inverting…
    • Answered

  • TS12A44514 - the consumption current of Vcc

    Resolved
    Other Parts Discussed in Thread: TS12A44514 HI all Would you mind if we ask TS12A44514? How much is the consumption current of Vcc? How much is the consumption current in case of "1 contact on(1 contact operation) " and "4 contact on(4 contact operation…
    • Resolved
    • Answered

  • TS12A44514 - ‎the equivalent circuit and the connection in case of power off

    Resolved
    Other Parts Discussed in Thread: TS12A44514 , TS5V330C , TS3DV642 Hi all Would you mind if we ask TS12A44514? <Question1> Do you have ‎the equivalent circuit of TS12A44514? Could you give us it? <Question2> When the device is the power off or t…
    • Resolved

  • TS12A44514 burned fail then damage issue

    Other Parts Discussed in Thread: TS12A44514 5228.CAN BUS-version 3.pdf Dear Sir,. there is TS12A44514 burned fail then damage issue with attachment , that`s a state in replug USB power source with LM1114 LDO then fail and burned., thank you Regards, …
    • Answered

  • TS12A44514 logic high threshold for 12V power supply

    Resolved
    Other Parts Discussed in Thread: TS12A44514 , TLC339 Hi, please help me to aunderstand: watch logic high threshold for TS12A44514 if a use 12 V power supply. Can I use for control 3,3 V logic level? In datasheet on page 4 (table for 12 V power) specified…
    • Resolved
    • Answered

  • RE: SN74CBT3125C: FET Switchi

    Resolved
    Hi Saminah, Thank you for your reply. VIH / VIL values are as follows. VIH = 2.3V (min) VIL = 0.55V (max) The input to OE is the output (Y3) of SN74LVC1G139. Please confirm the circuit diagram separately sent to your e-mail address. There was a proposal…

Didn't find what you are looking for? Post a new question.