Search tips
Showing 148 results View by: Thread Post Sort by

  • TS3A27518E: Application of TS3A27518E

    TI Thinks Resolved
    Part Number: TS3A27518E Hi TI Teams, Our project requires the use of two SPI flashes, compatible with wire brushes, and we plan to use two TS3A27518E for this application, the schematic block diagram is as follows: Is this design feasible? Or do you have…
    • Answered

  • TS3A27518E: Can this part to be used for Dual host?

    Resolved
    Part Number: TS3A27518E Hello, I have the query about the application of TS3A27518E. In the datasheet it shows that this IC can be used to multiplex the SDIO port for two SD-Cards and one Host controller. But in our application we have two Hosts and one…
    • Resolved
    • Answered

  • TS3A27518E-Q1: Different voltage level on input

    Resolved
    Part Number: TS3A27518E-Q1 Hi TI expert, I would like to confirm whether below idea will work. Since the IC act as a passive switch during on-state with certain ron. With VCC up to 3.3V, Could we bias NCx pins to 1.8V and NOx pins to 3.3V the using INx…
    • Resolved

  • TS3A27518E: data rate inquiry

    Answer Suggested
    Part Number: TS3A27518E Hi, TI support team TS3A27518ERTWR band witdh is 240Mhz. How much data rate is supported based on QSPI 6bit? Thanks. Regards, MJ

  • TS3A27518E: about 240MHz bandwidth

    TI Thinks Resolved
    Part Number: TS3A27518E Hi expert, Is the 240M bandwidth the -3dB bandwidth? If increasing the supply from 3.3V to 3.6V, would the bandwidth increase or decrease? Thanks.
    • Answered

  • RE: DRA746: eMMC1 switch to bus width failed with TS3A27518E multiplexer

    Resolved
    Hi, Macro. Thanks your reply. As far as I know, customer board can also boot from MMC2. For recent days debug, customer has work around way to skip this issue. because multiplexer just for factory MP only, not for normal use. So, I think we can close this…
    • Answered

  • TS3A27518E: TS3A27518E

    Resolved
    Part Number: TS3A27518E Hi, Is this bipolar technology? Is it susceptible to latchup? Do you have radiation test data?
    • Resolved
    • Answered

  • TS3A27518E: TS3A27518ERTWR for switching gigabit network signals

    Resolved
    Part Number: TS3A27518E Other Parts Discussed in Thread: TS3L501E Hi, I want to create a module based on TS3A27518ERTWR to switch b/w two networks. Network may be 10Mbps, 100Mbps or 1000Mbps. The idea is to connect three RJ-45 connectors to multiplexed…
    • Resolved

  • TS3A27518E: Design issue for TS3A27518E

    TI Thinks Resolved
    Part Number: TS3A27518E Other Parts Discussed in Thread: TMUX1208 , Hi, We design the CPU SPI switch and we consider to use the TS3A27518E or TMUX1208, the SPI rate is 12.5M But now we are afraid of the mulit-layer PCB will generate shock and the single…
    • Answered

  • TS3A27518E-Q1: TS3A27518E-Q1 Propagation Delay

    Resolved
    Part Number: TS3A27518E-Q1 Hi I cannot find any propagation delay information in the TS3A27518E-Q1 datasheet. What is the propagation delay through the TS3A27518E-Q1 (NCx/NOx to COM)? Best regards, Martin
    • Resolved

Didn't find what you are looking for? Post a new question.