Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.



Search tips
Showing 26 results View by: Thread Post Sort by
    Answered

  • UCC27524A1-Q1: How do we dealt with the maximum and recommended output current capability: 5A

    Resolved
    Part Number: UCC27524A1-Q1 Hi team, Its "Absolute Maximum Ratings" says that "Output pulsed source/sink current (0.5 µs)" is 5A. Does it mean its output pulse (0.5us) current should be lower than 5A? In addition, "Electrical…
    • Resolved
    • Answered

  • UCC27524A1-Q1: Think to keep the restrictions in parallel operation of UCC27524A1-Q1

    Resolved
    Part Number: UCC27524A1-Q1 Hello My customer connects UCC27524A1-Q1 INA and INB and uses two drivers in parallel. 8.3.6 of the data sheet states that dV / dt must be greater than 20V / us. How many ohms can the series resistor put into the input circuit…
    • Resolved
    • Answered

  • RE: UCC27524A1-Q1: Could it prevent load dump voltage by 20V by OCP?

    Resolved
    Hi Mamadou, Thank you for your supporting and sorry for making you confused. Actuary I mistook a part number. Correct one is LM7480-Q1 instead of UC27524. Regards, Ochi

  • UCC27524A1-Q1: Spice Model for UCC27524A1-Q1

    TI Thinks Resolved
    Part Number: UCC27524A1-Q1 Other Parts Discussed in Thread: UCC27524 Hi Team, Is possible to have the spice model of UCC27524A1-Q1? Regards, Fabio
    • Answered

  • UCC27524A1-Q1: Low side driver to control Charge and Discharge FET of BMS

    Resolved
    Part Number: UCC27524A1-Q1 Other Parts Discussed in Thread: UCC27524 Hi, We are developing 30S BMS and control the charge and discharge flow on low side using MOSFET. We need support on selection of MOSFET and Driver for charge current of 80A and Discharge…
    • Resolved
    • Answered

  • UCC27524A-Q1: What is the difference between UCC27524A-Q1 and UCC27524A1-Q1?

    Resolved
    Part Number: UCC27524A-Q1 Other Parts Discussed in Thread: UCC27524A1-Q1 , Hi team, Could you tell me the difference between UCC27524A-Q1 and UCC27524A1-Q1? They look really close and I cannot understand the difference of them. Regards, Ochi
    • Resolved

  • UCC27524A1-Q1: Circuit problems

    TI Thinks Resolved
    Part Number: UCC27524A1-Q1 Hi team, I have some trouble on UCC27524A1-Q1. INA and INB are shorted and OUTA and OUTB are also shorted. I use it on the low side, but it is often destroyed. I use it on the high side as well, but this is fine. I think there…
    • Answered

  • UCC27524A1-Q1: Differences between UCC27524AQDGNRQ1 and UCC27524A1QDGNRQ1

    Resolved
    Part Number: UCC27524A1-Q1 Hi experts, May I know the differences between these two devices? Thanks Sheldon
    • Resolved
    • Answered

  • UCC27524A1-Q1: Unexpected ringing on the gate drive output

    Resolved
    Part Number: UCC27524A1-Q1 Hi team, An unexpected ringing is observed on the gate driver output with UCC27524A1-Q1. As the FET drain voltage(HV) is hiked higher, the ringing looks to be generated as the attached waveform. 1) Is there any idea what possibly…
    • Resolved

  • UCC27524A1-Q1: What is the output voltage equation for UCC27524A1 driver based push pull converter.

    TI Thinks Resolved
    Part Number: UCC27524A1-Q1 Other Parts Discussed in Thread: UCC27524A-Q1 MOSFET driver UCC27524A1 based push-pull full bridge converter is the circuit I am working with (Dual rail). Here the output voltage equation from the application note: SPRABW0C is Vout…

Didn't find what you are looking for? Post a new question.