• UCC5350-Q1: The Vgs waveform of high side SiC MosFET using UCC5350 by bootstrap power supply in motor control application

  

  A.W

  TI Thinks Resolved

  Part Number: UCC5350-Q1 Other Parts Discussed in Thread: UCC5350 , UCC21551 Hi I'm testing UCC5350 for SiC driver in PMSM control application(600VDC input). I use bootstrap method to give the high side UCC5350 Power supply. The waveform of the Vgs is…

  • 9 days ago
  • Power management
  • Power management forum
Answered

• UCC5350: Quote# QE4A976 - Available Fit-Rate data....

  

  Adnan Zatarah

  Resolved

  Part Number: UCC5350 Hello, can you please advise if all available FIT rate data for P/N: UCC5350MCQDRQ1 can be provided for a customer? Thank you very much. Best regards Adnan

  • Resolved

  • 8 days ago
  • Power management
  • Power management forum

• UCC5350: Maximum working Frequency

  

  Ikenna Chukwuka

  TI Thinks Resolved

  Part Number: UCC5350 Hello, I would like to know the maximum frequency this device can operate at. Is it capable of frequencies ranging from 100 to 500 kHz? If there is not any device similar to this that can operate at that frequency with a Miller clamp…

  • 3 months ago
  • Power management
  • Power management forum

• UCC5350-Q1: Propagation delay min spec

  

  Scarlett Cao

  TI Thinks Resolved

  Part Number: UCC5350-Q1 Hi Team, Do we have the min value for propagation delay UCC5350-Q1? We only have typ and max spec in d.s. Customer software also need to take min into account. Thanks Scarlett

  • 3 months ago
  • Power management
  • Power management forum
Answered

• UCC5350-Q1: Working of miller clamp

  

  SRI RAM M A

  Resolved

  Part Number: UCC5350-Q1 Hello, i am using ucc5350-q1 gate driver for driving fs200r07pe igbt module. I am getting a fall time longer than i calculated and wanted to know whether the active miller clamp actually helps in reducing the fall time of the igbt…

  • Resolved

  • 4 months ago
  • Power management
  • Power management forum
Answered

• UCC5350: UCC5350 output not pulling close to VCC2

  

  Ikenna Chukwuka

  Resolved

  Part Number: UCC5350 Hello, I need some help here and this is not the first time I am asking about this device. As shown in the diagram, I am supplying the VCC1 and IN+ with 5V and the VCC2 with 20V. VEE2 with -5V. Ignore the -3V. When I probe the output…

  • Resolved

  • 8 months ago
  • Power management
  • Power management forum
Answered

• UCC5350: Spice model

  

  onda.kohei

  Resolved

  Part Number: UCC5350 I would like to request you to check the SPICE model of UCC5350SBD. The model of UCC5350MCD has been modified to avoid "False turn ON of upper NMOS.". On the other hand, the model of UCC5350SBD has not been modified. Does the…

  • Resolved

  • 6 months ago
  • Power management
  • Power management forum
Answered

• UCC5350: UCC5350M Enable / Disable function

  

  user5956241

  Resolved

  Part Number: UCC5350 Dear TIer, Can you help us to provide the similar as enable/disable function schematic for UCC5350M with MCU? thanks!

  • Resolved

  • 6 months ago
  • Power management
  • Power management forum
Answered

• RE: UCC5350: Can I drive two MOSFET in parallel simultaneously with a UCC5350 with a Miller clamp?

  

  Don Dapkus

  Resolved

  Hi, Hailan, I can't comment on future products in development in a public forum. Best regards, Don

  • 8 months ago
  • Power management
  • Power management forum

• UCC5350-Q1: Miller Clamp Activation Time

  

  Andy Snawerdt

  TI Thinks Resolved

  Part Number: UCC5350-Q1 Hi Team, I'm working with my customer on an OBC application and would like to understand what the activation time of the miller clamp FET is once the gate get's below 2V. Thanks for the support! Regards, Andy

  • 7 months ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.