TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 38 results View by: Thread Post Sort by
    Answered
  • UCC5870-Q1: unmask fault operation

    Sherry Liang
    Sherry Liang
    Resolved
    Part Number: UCC5870-Q1 Dear team, 1. If one fault is masked, then nFLT pin won't pull low. Does the FS_STATE_XXX operate? For example, if VCC1 OVLO fault is masked, and we set bit14=0. When this fault occurs, OUTH/OUTL will have no action due to being…
    • Resolved
    • 6 days ago
    • Power management
    • Power management forum
  • UCC5870-Q1: ADC operation preconditions

    Rafael Lindner
    Rafael Lindner
    TI Thinks Resolved
    Part Number: UCC5870-Q1 Hello, I am using the UCC5870-Q1 A/D converter with "Edge-Sampling-Mode" configuration. I have to read some ADC data after the device enters the "Active" operation mode for several system checks before switching-on the…
    • 14 days ago
    • Power management
    • Power management forum
  • Answered
  • UCC5870-Q1: GM fault

    Sherry Liang
    Sherry Liang
    Resolved
    Part Number: UCC5870-Q1 Other Parts Discussed in Thread: TEST Dear team, 1. Could you please tell me our device how to monitor gate voltage? We found that when we disconnected the resistor Rgon between OUTH and Gate, our device will report GM fault. 2.…
    • Resolved
    • 18 days ago
    • Power management
    • Power management forum
  • UCC5870-Q1: VGTH read back

    [FAE] Andrew Wang
    [FAE] Andrew Wang
    TI Thinks Resolved
    Part Number: UCC5870-Q1 Hi Team, Customer found 2 different formula for calculating VGTH. Which one customer should be using, thanks! Andrew VGTH = VADCDATA8 × 8 VGTH = DATA_OUTH(decimal) × 3.519mV
    • 1 month ago
    • Power management
    • Power management forum
  • RE: UCC5870-Q1: SPI TX CRC check

    Andy Robles
    Andy Robles
    Hi Tobias, Thank you for your patience. Tobias Haerter said: 1. I could no read the TX CRC data from the CRCDATA register. The values change every time. What is wrong at my implementation. I write to the TX CRC register and then read it, but the read value…
    • 9 days ago
    • Power management
    • Power management forum
  • UCC5870-Q1: ADCDATA8 read back as 0

    [FAE] Andrew Wang
    [FAE] Andrew Wang
    Part Number: UCC5870-Q1 Hi Team, Customer uses 6 UCC5870 on the board - as U/V/W. When read back ADCDATA8, customer found only one out of 6 has value, the rest shown 0. Customer mentioned they did Address-based H/W connection, and did addressing for each…
    • 1 month ago
    • Power management
    • Power management forum
  • UCC5870-Q1: UCC5870-Q1 - gate voltage monitoring

    Andreas Storbeck
    Andreas Storbeck
    TI Thinks Resolved
    Part Number: UCC5870-Q1 Dear TI experts, we are currently evaluating a UCC5870-Q1 gate driver IC in combination with SiC MOSFET. Our goal is to monitor the voltage of the gate of the mosfet as close as possible to the real device due to safety reasons…
    • 3 months ago
    • Power management
    • Power management forum
  • Answered
  • UCC5870-Q1: AI* input RC filter for IGBT temp sensing through integrated temp diode

    Dongbao Zhou
    Dongbao Zhou
    Resolved
    Part Number: UCC5870-Q1 hi, Customer would like to decrease the RC filter frequency to improve the noise filter performance (RC to be around few ms), understand higher R cause poor accuracy and higher C reduce the response time. Is there any limitation…
    • Resolved
    • 15 days ago
    • Power management
    • Power management forum
  • UCC5870-Q1: OUTH keep high for a long time

    Sherry Liang
    Sherry Liang
    Part Number: UCC5870-Q1 Dear team, Could you please help answer below two questions? Thanks! 1. Could you please tell me whether our Bootstrap function can support OUTH remains high for 2 hours? In my understanding, the bootstrap cap needs to be char…
    • Resolved
    • 1 month ago
    • Power management
    • Power management forum
  • UCC5870-Q1: Simplis Submodel

    Marvin Gasis Arcangel
    Marvin Gasis Arcangel
    TI Thinks Resolved
    Part Number: UCC5870-Q1 Hi Experts, Our customer mentioned that the available Simplis model on the UCC5870-Q1 webpage is unfortunately not complete. Several submodels are not included. I could not verify this concern as I do not have the software to do so…
    • 3 months ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.