Search tips
Showing 124 results View by: Thread Post Sort by

  • RE: CCS/UCD3138A64: Problem running the code for blinky in UCD3138A64.

    Hello Shoeb Since this thread has been inactive for some time, I am going to close it. Please re-open a new thread if you need more support. Kind Regards Cormac

  • RE: CCS/UCD3138A64: How to set UCD3138A64 I2C_CLK(pin19) as GPIO?

    You can set I2C_CLK to GPIO, but not through GLBIO registers. You can do this through I2CCTRL3/PMBCTRL3 register (Address FFF7F720). Using the bits SCL_DIR, SCL_VALUE, SCL_MODE. Please refer to UCD3138A64 technical reference manual: www.ti.com/.../sluub54b…
    • Answered

  • CCS/UCD3138A64: How to use ucd3138A64 to communication with eeprom buy SPI on EVM board。

    Resolved
    Part Number: UCD3138A64 Tool/software: Code Composer Studio Hello: I found an Eeprom AT45DB821E on this board , now i want to use ucd3138A64 to communication with it buy SPI。i following Programmer’s Manual to write spi program is no work。Have any ucd3138xx…
    • Resolved
    • Answered

  • CCS/UCD3138A64: How should I do for UCD3138A64 RTC_IN_1_8(pin62) when not use this function?

    Resolved
    Part Number: UCD3138A64 Tool/software: Code Composer Studio Hi I find UCD3138A64 RTC_IN_1_8(pin62) have 1.8V when I measure on this pin. How should I do for UCD3138A64 RTC_IN_1_8(pin62) when not use this function? Short to GND, put high to VCC…
    • Resolved

  • UCD3138A64: UCD3xxx/UCD9xxx Device GUI

    TI Thinks Resolved
    Part Number: UCD3138A64 hi All, My customer did the same step before, it never pop up this windows before. But now shows this windows, it may have some problem in their factory side. Can you tell me why this windows shows up?
    • Answered

  • CCS/UCD3138: UCD3138A64

    Resolved
    Part Number: UCD3138 Tool/software: Code Composer Studio Hi everyone, FE0 is for voltage mode and FE1 for current mode if i want convert dc input to dc output, shold i consider both FE0 and FE1 or only FE0 i am fully confused could any one tell me please…
    • Resolved
    • Answered

  • UCD3138A64: PMP21529 Source Code

    Resolved
    Part Number: UCD3138A64 Other Parts Discussed in Thread: PMP21529 , BQ40Z50 , UCD3138A Hi We are evaluate a new battery charger project using 4 switch buck-boost converter,we're taking a digital controller due to the SMBus requirement . the PMP21529…
    • Resolved

  • UCD3138A64: UCD3138A64 checksum calculation.

    TI Thinks Resolved
    Part Number: UCD3138A64 Other Parts Discussed in Thread: UCD3138064 , UCD3138 Hello, I have to develop a firmware to compare the checksum of the Flash memory of the UCD3138A64 (once it is programmed - using the command 0xEF) and the checksum of the…
    • Answered

  • RE: UCD3138A64: How to configure UART for UCD3138A64?

    Resolved
    Thanks again, Ian! This code in fact makes UART transmit data. The thing that I would have never guessed is to assert SW_RESET for setting the configuration. I can't find anything about that in the Technical Reference Manual. And actually, it seems…
    • Answered

  • RE: UCD3138A64: unable to get UCD3138A64 into program mode

    Resolved
    YES! Thanks, Ian, that was it! The funny thing is that actually I remember about this backdoor... but that's not enough to realize that putting this jumper on is necessary. Best regards, Adam

Didn't find what you are looking for? Post a new question.